Simex’s versatile tool helps in tunnel excavation duties

Italian firm Simex has developed a versatile tool for use in tunnel excavation applications. This proven piece of equipment has been used to help construct a key tunnel link in Italy, close to the border with Switzerland. Work on the Varzo Tunnel has been carried out by Italian contractor Ceprini Costruzioni (CC).
March 13, 2013 Read time: 2 mins
Italian firm 1141 SIMEX has developed a versatile tool for use in tunnel excavation applications. This proven piece of equipment has been used to help construct a key tunnel link in Italy, close to the border with Switzerland. Work on the Varzo Tunnel has been carried out by Italian contractor Ceprini Costruzioni (CC).

The final phase of this three-phase project required the installation of two-hinged steel ribs every 1.75m, anchored to ties with a C-shaped fastening element (totalling 44 elements). Another task was the laying of a 10x10cm, 6mm diameter wire mesh covering up to 18cm of fibre-reinforced shotcrete. One of the major challenges of the third phase was to cut around 20cm deep and 40cm wide into the crown of the tunnel in order to create the inserts for the steel ribs.  A solution to the problem was offered by Simex, which designed a special rotary cutter derived from the model TF 800.

Attached to a 2300 Komatsu PC138 US short-radius excavator, and featuring a modified boom and special bracket (both supplied by Grifo workshops in Perugia), the rotary cutter made it possible to make the inserts for the steel ribs.  The use of a hydraulic breaker for the application was immediately discarded by CC due to the length of time associated with its use and the lack of optimum precision, with the possible introduction of dangerous vibrations into the crown near the deteriorated area. CC decided to use a pair of Komatsu PC 138 US excavators and two Simex TF 800/V rotary cutters. The cutters were equipped with drums measuring a width of 400mm and diameter of 1100mm, and fitted with 144 Betek VC 33 bits with a 22mm bit holder.  Both cutters were said to have proven productive and reliable and were operated without interruption for 164 hours each.

Stand: B3.222

www.simex.it

View more videos
View more stories

For more information on companies in this article

Simex
Komatsu

Related Content

  • Simex RS 16 planer for creating rumble strips
    March 22, 2017
    Simex says that its new RS 16 planer for creating rumble strips is an efficient alternative to costly specially designed machines or small manual equipment Rumble strips created by intermittent milling of the wearing course offer the advantage of lower production costs and a higher durability than those made using elastoplastic adhesives - laminates. Compared to adhesives, rumble strips created by surface milling also have the important advantage of being indented and not raised, a characteristic that av
    Read More
  • RDS launches LOADMASTER a100 weigh system at bauma
    February 12, 2013
    RDS Technology is launching the LOADMASTER a100 on-board weighing system that is described by the UK-based manufacturer as an industry benchmark in terms of accuracy and ease of use in difficult conditions and terrains. The all-new CAN-based system combines cutting edge sensor technology and signal processing techniques providing precise and consistent weight information, says RDS.
    Read More
  • RDS launches LOADMASTER a100 weigh system at bauma
    January 6, 2017
    RDS Technology is launching the LOADMASTER a100 on-board weighing system that is described by the UK-based manufacturer as an industry benchmark in terms of accuracy and ease of use in difficult conditions and terrains. The all-new CAN-based system combines cutting edge sensor technology and signal processing techniques providing precise and consistent weight information, says RDS.
    Read More
  • Doka showcases Cut&Cover tunnel construction solution
    January 6, 2017
    Austrian firm Doka will be showcasing at bauma its first system to be specifically designed and optimised for cut-and-cover tunnel construction. With Doka CC (Cut and Cover), different types of traffic tunnel, such as rail or road tunnels, are said to be able to be built quickly, efficiently and safely. Doka says the creation of its innovative tunnel system was made possible only by the use of hi-tech construction materials and products such as the Composite formwork beam I tec 20. The choice of high-grade
    Read More

Highlighted Content