Technology to ensure continuity and quality for asphalt production

A variety of complex factors are involved in the production of hot asphalt mixes, with the process vulnerable to sudden stoppages of the equipment. The problems caused by a need for unplanned maintenance are high, as the cost of a plant stoppage is high. In order to minimise disruptions to production, new technologies can be used for wear components. Electronic monitoring of asphalt plant motors during production can boost efficiency, replacing corrective maintenance with preventive and predictive maintenan
June 4, 2019 Read time: 3 mins
Monitoring component performance at the control panel can highlight wear issues
A variety of complex factors are involved in the production of hot asphalt mixes, with the process vulnerable to sudden stoppages of the equipment. The problems caused by a need for unplanned maintenance are high, as the cost of a plant stoppage is high. In order to minimise disruptions to production, new technologies can be used for wear components. Electronic monitoring of asphalt plant motors during production can boost efficiency, replacing corrective maintenance with preventive and predictive maintenance.


Preventive maintenance is a widely used method for maximising equipment uptime. Scheduled stoppages of machines are made according to the expected amount of wear, based on average statistics for generic equipment applications. Predictive maintenance is much more complex because it considers the condition and use of components, according to a specific application. This is used in order to schedule maintenance at the correct time. According to Marcelo Zubaran, application engineer and product specialist at 6241 CIBER Equipamentos Rodoviários, “Obtaining the correct information at the right moment regarding a component wear or a tendency of failure of a motor is a major advantage to asphalt mix production.” Predictive maintenance can only be implemented when using systems that continuously monitor components. Both mechanical and electronic sensors may be used for this process.

A predictive maintenance plan can be used for components featuring an abrasive wear rate, which develops over the lifetime of a tool. A plant’s mixer vanes exhibit wear proportional to the time they have been used. Examining the wear on the vanes, it is possible to predict when to replace the component. The condition of the plant’s bag filters are monitored indirectly during production by pressure meters installed in the filter box. This system indicates if the filters are likely to saturate. The meters help to prevent damage to the filter elements as well as wear to the plant hood.

State-of-the-art technologies can also be employed, such as constant monitoring of the power consumption of motors during production. When a motor starts drawing more power than usual, it can be a sign that a fault is developing. This type of fault diagnosis system also provides real-time information on the operating conditions of the motors to the plant operator. “If any of the plant motors are not operating at their optimum performance, an alarm is triggered immediately. The operator can select to stop production of an asphalt mix and then check the condition of the motor and even stop the plant if necessary. In this way, predictive maintenance technology allows the user to perform preventive maintenance," according to Zubaran.

For this technology to work, it is necessary for the motors to be connected to an electrical current measuring device. This system then has to be connected to a data transmission network. Frequency inverters are used to vary the speed of motors and are also capable of measuring the current running through a motor. In addition, soft start technologies used for big motors can also measure the electric current. Integral starter systems can be utilised to measure the current passing through motors also. These devices require a network interface to allow data to pass over to the plant’s computer, which will then analyses the information using software.

Materials

For more information on companies in this article

Related Content

  • Paving a new racing circuit
    February 2, 2022
    The use of reduced temperature asphalt in a road construction project in Germany has helped to lower emissions
    Read More
  • Caterpillar C series articulated dump trucks move with the times
    May 19, 2015
    Caterpillar has raised the bar for articulated dump truck performance with the introduction of its C Series to replace its B series ADTs. All the new Cat 735C, 740C EJ and 745C ADTs have engines that meet US EPA Tier 4 Final/EU Stage IV emissions standards. The machines also incorporate many new and upgraded features designed to boost the operator’s efficiency, ensure a longer life cycle of the vehicle and save fuel. Rated payload capacities for the new models are 32.7tonnes for the 735C, 38tonnes for the 7
    Read More
  • Volvo CE’s 3D parts printing
    March 26, 2018
    Volvo CE says that it will utilise 3D parts printing technology to supply customers. The firm says that this will allow it to supply quality components quickly and at lower cost to customers. By using 3D parts printing the firm also says it will be able to carry out prototype testing of components more speedily than in the past. “We are supporting customers through the life cycle of their equipment,” said Jasenko Lagumdzija, anager of Business Support at Volvo CE. “It’s especially good for older machines
    Read More
  • Asphalt: checking properties
    July 18, 2012
    Specialist equipment is available for carrying out a variety of important tests on asphalt It is important to know how asphalt will react to various conditions such as heat, cold and traffic loads when it is laid on roads. Project specifications will give detailed criteria of what is required, and companies will either ask outside laboratories to make sure the material meets the specs, or will often carry out such tests themselves with trained staff in an on-site laboratory. This will be equipped with the
    Read More

Highlighted Content