Better road surfaces to last longer

Preservation can make roads perform better and last longer - and save money in the long run. Kristina Smith reports BAM Wegen has laid the first ever half-warm porous asphalt section on a major highway in the Netherlands. The asphalt for the 500m-long test section on the A18 near Varsseveld was produced at 105°C rather than 160°C, representing a saving on energy and CO2 emissions of around 30%.
August 23, 2013 Read time: 4 mins
On the A18 near Varsseveld in The Netherlands in April this year, BAM Wegen demonstrated that it is possible to produce and pave Porous Asphalt at around 100°C
RSS

Preservation can make roads perform better and last longer - and save money in the long run. Kristina Smith reports

7456 BAM Wegen has laid the first ever half-warm porous asphalt section on a major highway in the Netherlands. The asphalt for the 500m-long test section on the A18 near Varsseveld was produced at 105°C rather than 160°C, representing a saving on energy and CO2 emissions of around 30%.

The trial follows on from the successful application of the half-warm porous asphalt, LEAB-PA, on a rural road, the N314 near Zutphen in 2010. “The results of this short test-section were so good that we and the Dutch Highway Administration, Rijkswaterstaat, thought we were ready for a large test-section on a highway,” said BAM Wegen road engineer Marco Oosterveld.
The use of porous asphalt, a surface layer, is mandatory on the Dutch primary network. One of the main reasons why porous asphalt has to be replaced is due to ravelling, the loss of stones from the road surface, which means that it is critical to get the composition of the mix right, according to BAM Wegen. The firm is part of the Royal Bam Group and laid over 150,000tonnes of low-energy asphalt (LEAB) in base layers in the Netherlands between 2011 and 2012. This year it has installed the LEAB technology at three of its eight asphalt plants and has sold the right to use the patented production technique to a large Japanese road construction company, and has also recently completed similar negotiations with a large asphalt producer in Germany.

The contractor also laid a second test-section on the A18, which is part of the IGO-ON-project for the Dutch Ministry of Transport, Public Works and Water Management, surfaced with a fibre reinforced porous asphalt. Panacea fibres, fine acrylic fibres, were added to the mix to prevent bitumen erosion and extend surface life.

The cost of the half-warm porous asphalt is similar to traditional mixes, said Oosterveld, with the investment in technologies more-or-less equivalent to the savings due to lower energy consumption during production. The next step will be to monitor the two test sections, comparing their performance to standard porous asphalt. BAM will use its own road research laboratory in Utrecht to perform tests on cores taken from the test strips. The firm has received a grant for research into sustainable innovations in processing and use of asphalt through the European program LIFE +. The four-year research period has been named AP ² LE (Low Energy and Emission Asphalt Pavements).

Iterchimica asphalt rejuvenator

A green rejuvenator from Italian road pavement asphalt additive specialist 252 Iterchimica is proving popular. The product, Iterlene ACF1000 Green, allows up to 40% RAP to be used whilst lowering the temperature required at the asphalt plant, and emissions, by up to 50%. “If you used 40% RAP normally without using an additive, you must heat the virgin aggregate up to 250° or 270°C,” said Alessandro Giannattasio of Iterchimica. “When you add the RAP, you create a lot of steam, emissions, and smell. By using our additive you can lower the temperature down to 160° or 170° which is the normal mixing temperature.”

The combination of a higher proportion of RAP combined with less energy use at the plant can make for cost savings, said Giannattasio. Launched three years ago, with other products forming Iterchimica’s ‘Green Line’ range, ACF 1000 has found favour with Italian contractors. In Italy the roads industry faces the twin challenges of cost -cutting and meeting stringent environmental rules relating to emissions at asphalt plants. “All the contractors are trying to squeeze prices down, so they are looking to use as high a quantity of RAP as they can,” said Gianattasio. “At the same time the authorities here are sensitive to the problem of emissions. Plants that don’t meet the reduction targets are closed down.”

Iterchimica also reports the use of its rejuvenator in Belgium, Switzerland and Spain. And the company is talking to UK contractors following on from a research report from the UK’s Transport Research Laboratory which confirmed ACF1000’s rejuvenating properties.






















RSS
Materials

For more information on companies in this article

Related Content

  • How waste plastic and soybean oil are helping our roads last longer
    April 13, 2018
    A new super-modifier is born from waste plastic in Italy and a soybean-based rejuvenator from the US spreads from its home market. By Kristina Smith The two bitumen technologies featured this month come from almost opposing sources. One emerges from the human-created plastic waste plaguing our planet, the other from a plant. However, both technologies have been created with the same aims: to increase the life of roads, saving cost and ultimately reducing the impact of road building on the planet. A coll
    Read More
  • Review of the research activities on the behaviour of Iterlene
    November 2, 2012
    The use of reclaimed asphalt pavement (RAP) is common practice in many countries. The aged bitumen from RAP has a lower penetration and is more viscous than it was when first mixed. The reclaimed bitumen is generally balanced by the addition of fresh binder softer than the traditional one used to produce hot mixes. However, balancing penetration and softening point or viscosity does not produce an identical bitumen to the original one. One fundamental option is the regeneration of the aged binder in order t
    Read More
  • Warm asphalt is a hot topic
    June 12, 2012
    Lower temperature mixes – a key advance in bitumen technology - Kristina Smith reports Warm and cold mix asphalts were not on the original agenda for this year’s Eurasphalt & Eurobitume Congress, being held in Istanbul in June. But when the organisers took a look through the papers submitted for their sustainability-themed event, they realised that this is one of the industry’s hottest topics. “We hadn’t quite anticipated the high level of research in this area,” says E&E’s technical programme committee c
    Read More
  • Global pressures driving bitumen developments
    June 19, 2015
    A raft of global pressures is driving developments in the materials and equipment we use for the handling, storage and treatment of bitumen. The goal is to achieve better performance and longer life for less financial outlay, and at the same time overcome the challenges of inconsistent and varying bitumen supplies. Kristina Smith reports.
    Read More

Highlighted Content