Better road surfaces to last longer

Preservation can make roads perform better and last longer - and save money in the long run. Kristina Smith reports BAM Wegen has laid the first ever half-warm porous asphalt section on a major highway in the Netherlands. The asphalt for the 500m-long test section on the A18 near Varsseveld was produced at 105°C rather than 160°C, representing a saving on energy and CO2 emissions of around 30%.
August 23, 2013 Read time: 4 mins
On the A18 near Varsseveld in The Netherlands in April this year, BAM Wegen demonstrated that it is possible to produce and pave Porous Asphalt at around 100°C
RSS

Preservation can make roads perform better and last longer - and save money in the long run. Kristina Smith reports

7456 BAM Wegen has laid the first ever half-warm porous asphalt section on a major highway in the Netherlands. The asphalt for the 500m-long test section on the A18 near Varsseveld was produced at 105°C rather than 160°C, representing a saving on energy and CO2 emissions of around 30%.

The trial follows on from the successful application of the half-warm porous asphalt, LEAB-PA, on a rural road, the N314 near Zutphen in 2010. “The results of this short test-section were so good that we and the Dutch Highway Administration, Rijkswaterstaat, thought we were ready for a large test-section on a highway,” said BAM Wegen road engineer Marco Oosterveld.
The use of porous asphalt, a surface layer, is mandatory on the Dutch primary network. One of the main reasons why porous asphalt has to be replaced is due to ravelling, the loss of stones from the road surface, which means that it is critical to get the composition of the mix right, according to BAM Wegen. The firm is part of the Royal Bam Group and laid over 150,000tonnes of low-energy asphalt (LEAB) in base layers in the Netherlands between 2011 and 2012. This year it has installed the LEAB technology at three of its eight asphalt plants and has sold the right to use the patented production technique to a large Japanese road construction company, and has also recently completed similar negotiations with a large asphalt producer in Germany.

The contractor also laid a second test-section on the A18, which is part of the IGO-ON-project for the Dutch Ministry of Transport, Public Works and Water Management, surfaced with a fibre reinforced porous asphalt. Panacea fibres, fine acrylic fibres, were added to the mix to prevent bitumen erosion and extend surface life.

The cost of the half-warm porous asphalt is similar to traditional mixes, said Oosterveld, with the investment in technologies more-or-less equivalent to the savings due to lower energy consumption during production. The next step will be to monitor the two test sections, comparing their performance to standard porous asphalt. BAM will use its own road research laboratory in Utrecht to perform tests on cores taken from the test strips. The firm has received a grant for research into sustainable innovations in processing and use of asphalt through the European program LIFE +. The four-year research period has been named AP ² LE (Low Energy and Emission Asphalt Pavements).

Iterchimica asphalt rejuvenator

A green rejuvenator from Italian road pavement asphalt additive specialist 252 Iterchimica is proving popular. The product, Iterlene ACF1000 Green, allows up to 40% RAP to be used whilst lowering the temperature required at the asphalt plant, and emissions, by up to 50%. “If you used 40% RAP normally without using an additive, you must heat the virgin aggregate up to 250° or 270°C,” said Alessandro Giannattasio of Iterchimica. “When you add the RAP, you create a lot of steam, emissions, and smell. By using our additive you can lower the temperature down to 160° or 170° which is the normal mixing temperature.”

The combination of a higher proportion of RAP combined with less energy use at the plant can make for cost savings, said Giannattasio. Launched three years ago, with other products forming Iterchimica’s ‘Green Line’ range, ACF 1000 has found favour with Italian contractors. In Italy the roads industry faces the twin challenges of cost -cutting and meeting stringent environmental rules relating to emissions at asphalt plants. “All the contractors are trying to squeeze prices down, so they are looking to use as high a quantity of RAP as they can,” said Gianattasio. “At the same time the authorities here are sensitive to the problem of emissions. Plants that don’t meet the reduction targets are closed down.”

Iterchimica also reports the use of its rejuvenator in Belgium, Switzerland and Spain. And the company is talking to UK contractors following on from a research report from the UK’s Transport Research Laboratory which confirmed ACF1000’s rejuvenating properties.






















RSS
Materials

For more information on companies in this article

Related Content

  • Astec develops innovative asphalt plant with additional recycling capability
    June 23, 2015
    Astec’s headline RAP plant can use up to 65% RAP content As it does for the 50% double barrel system aggregate dryer/drum mixer model, Astec is guaranteeing that its customers will get the increased percentage. The unit runs at 181-360tonnes/hour production (200-400UStons/hour). Astec, based in Chattanooga, Tennessee, manufactures all of their state-of-the-art Hot Mix Asphalt plants in the US. They introduced the first double barrel plant in 1989, according to executive vice president Steven Claude, during
    Read More
  • Rubber recycling for South African roads
    November 5, 2012
    South Africa takes crumb rubber use to the next level - *Anders Marschall Jensen The preservation of the environment is a global concept, and in the road construction industry, it is all about preservation of roads. In earlier days, roads were built with the primary goal of moving passenger traffic from one place to another, but these days, roads are very different. Not only is there passenger traffic, and more of it, but roads must also deal with extensive movement of products in heavy vehicles. Therefore,
    Read More
  • Airport's high demands on asphalt and concrete techniques
    July 11, 2012
    Airport runway, taxiway and parking areas make high demands on paving requirements, both with concrete and asphalt techniques. Mike Woof reports. High quality surface finishes are required in airport environments for runways, taxiways and aircraft parking areas. Because of the speed at which aircraft take off and land and the massive forces exerted due to the weight of the aircraft, particularly during landing, runway structures need to be incredibly strong. The surfaces also have to be constructed to very
    Read More
  • The Danish Road Directorate is testing climate-friendly asphalt
    June 4, 2018
    Over the next few weeks, Denmark is hosting a world-premiere in the field of green infrastructure. A busy section of the motorway exiting the greater area of Copenhagen northbound towards Elsinore has been chosen is being used for the trials. This is the first of several roads on the Danish state road network to receive a special climate-friendly asphalt, as part of the development of pavements that reduce emissions from road traffic. This type of asphalt has been developed over the last decade and is the
    Read More

Highlighted Content