Compact planer under test

BOMAG has carried out a successful series of demonstrations of its new BM500/15 compact milling machines in Berlin. The machine was tested at the Representative Offices of Rheinland-Palatinate to the Federal Government and the European Union in Berlin and for the first time the planer carried out practical tests in the grounds of the company's Berlin Branch. A total of around 100 guests watched a highly convincing demonstration. After a reception at the Representative Offices of Rheinland-Palatinate delegat
February 22, 2012 Read time: 3 mins
172 Bomag has carried out a successful series of demonstrations of its new BM500/15 compact milling machines in Berlin. The machine was tested at the Representative Offices of Rheinland-Palatinate to the Federal Government and the 1116 European Union in Berlin and for the first time the planer carried out practical tests in the grounds of the company's Berlin Branch. A total of around 100 guests watched a highly convincing demonstration. After a reception at the Representative Offices of Rheinland-Palatinate delegates saw the machines being run at the company's Berlin Branch.

Nine tests were carried out by the new planer. A defective concrete channel had to be milled on both sides for 500mm in a total of three strips around 40mm deep. The quick-change LA 15 (500mm) milling drum was selected and was able to leave a clean and precise edge and a level surface. The conveyor belt on a compact planer often has to be disconnected for certain work such as to position the rear of the machine close to a wall and the faster this can be achieved, the less downtime for the contractor. The process time including dismounting from the machine, lowering the scraper and setting off again took 2 minutes 30 seconds. Planing a manhole cover is another key task and the machine was able to perform this quickly and efficiently. Changing the drum is also important for versatility and this job took 8 minutes 6 seconds. The disconnected conveyor belt was now reconnected - just as easily and quickly. This ensures that the versatility of this BOMAG planer is fully utilised. This procedure is only carried out on-site if the conveyor belt is easily disconnected and connected, ensuring that hand cutting work in tight spaces is reduced. The sixth task involved the POWER DRUM, a milling drum with 20mm line spacing, to plane out an 80-120mm deep crack in the asphalt and to load the milled material. The next task was to plane a concrete channel, a speciality for the POWER DRUM. With the drum's large line spacing, the individual cutters generate greater cutting power and pulverise the hard concrete. The last two tasks involved examining ease of servicing. Checking the spray bar is said to be particularly easy, just like the other service points. All are easily and quickly accessible on the right side of the machine where everything is in view and nothing gets forgotten.
Recycling

For more information on companies in this article

Related Content

  • BOMAG’s versatile new rubber tyred compactor
    May 17, 2017
    BOMAG says that its new BW 28 RH pneumatic roller offers improved performance, with easily adjustable ballasting, an ergonomic cabin and high productivity. The front end of the BW 28 RH is designed for better visibility of the wheel surface, allowing the operator to check whether the wheels are sufficiently wet to prevent asphalt from sticking. The clear view of the work area also boosts efficiency as it is possible to work accurately to asphalt edges or joints. The BW 28 RH is said to boost versatility due
    Read More
  • Developments in noise-reducing road surfaces
    February 17, 2012
    Mixtures with special additives are being produced for roads, offering noise reduction and aiding recycling. Patrick Smith reports. Noise-reducing road surfacings have been used in motorway construction for some time. But relatively new are noise-optimised surfacings used on roads in towns that do not follow a standard concept.Road trials with these materials have taken place in Germany since 2007 and have been prioritised due to the European Union Guidelines on the Assessment and Management of Environmenta
    Read More
  • Milling and paving for a highway repair in Oklahoma
    April 5, 2017
    Milling and paving work has helped restore the road surface on an important stretch of highway in the US state of Oklahoma. US Highway 62 is a key route, running 3,597km from to Niagara Falls, New York, at the Canada–US border to the Mexico-US border at El Paso in Texas. It is the only east-west United States numbered highway that connects Canada with Mexico through the US, making it a key transport route. A 12km section of US 62 where it runs through Oklahoma recently benefited from a much-needed rebuild,
    Read More
  • Australian bridge slides into position
    July 18, 2012
    A heavy rail crossing as part of Australia's EastLink motorway demanded great ingenuity and careful planning Most of the 88 bridges on the EastLink tolled motorway in, Melbourne, Australia were kept as simple and straightforward as possible. Contractor Thiess John Holland (TJH) developed its own precast yard 150km from the city, which provided many of the prefabricated materials required for the structures. This offered speed and economy while logistics and sequencing were vital for their erection. But the
    Read More

Highlighted Content