Dynatest’s FastFWD8002 deflectomer picks up more points per hour

Pavement engineering specialist Dynatest has improved its best-selling falling weight deflectometer, allowing it to not just collect more data, but collect it faster. The Danish company said its FastFWD8002, which was unveiled at the Transportation Research Board annual meeting in Washington in January, is five times faster than the previous model. The FastFWD8002 collects 75% more test points per hour, meaning it can have around 45% less traffic exposure. The previous unit is upgradeable to FastFWD80
April 28, 2015 Read time: 2 mins
Pavement engineering specialist 2597 Dynatest has improved its best-selling falling weight deflectometer, allowing it to not just collect more data, but collect it faster.

The Danish company said its FastFWD8002, which was unveiled at the 2774 Transportation Research Board annual meeting in Washington in January, is five times faster than the previous model.

The FastFWD8002 collects 75% more test points per hour, meaning it can have around 45% less traffic exposure. The previous unit is upgradeable to FastFWD8002 specification.

The FastFWD8002, which does not use hydraulics, has the same sensor setup and user interface as the FWD model and so no major training of operators is needed. It is available as a trailer or a truck-mounted version meeting all FWD standards worldwide.

The deflectometer applies a dynamic load that simulates the loading of a moving wheel. The pavement response is analysed with Dynatest's ELMOD (Evaluation of Layer Moduli and Overlay Design) software to determine the elastic moduli, stresses and strains of each modelled layer. ELMOD reports the weakest layer of failure, residual life, and determines the optimum rehabilitation alternatives.
Asphalt milling, paving & compaction

For more information on companies in this article

Related Content

  • ERIC 2016: What shape the ‘Smart Road’?
    February 7, 2017
    Optimism about the future of highways worldwide abounded at the inaugural European Road Infrastructure Conference (ERIC) in Leeds, UK Around 500 delegates passed through the varied sessions during the three-day event at the Royal Armouries Museum in the northern English city of Leeds. They came away with many visions of what a motorway and road could look like. But what speakers at the event - co-organised by the Brussels-based European Union Road Federation (ERF) and the UK’s Road Safety Markings Ass
    Read More
  • US highway rebuild uses hard-wearing asphalt
    July 18, 2012
    Guntert & Zimmerman equipment is being used to create a new hard-wearing asphalt surface on a key Interstate highway in the US state of Kansas as Mike Woof reports A busy Interstate highway in the US is now benefiting from a new, long-lasting surface. The road, Interstate 70 in Western Kansas, was in need of resurfacing. The full-depth asphalt roadway, up to 508mm thick in certain sections, had reached the end of its working life.
    Read More
  • Wirtgen W 210i: A good grip on the TT Circuit Assen
    October 16, 2015
    The 4.5km TT circuit in Assen, Netherlands, is one of Europe’s iconic motorcycle race tracks built specifically for championship two-wheel races. But years of hard and fast racing had created undulations 3-8 mm high along the start and finishing stretches. Drivers had to brake before turns. Even so, their machines would judder and threaten to be uncontrollable. It was therefore necessary to profile the raceway over an area of 3,000m² to restore the surface’s skid resistance. Enter GMS Fahrbahnsanierun
    Read More
  • Gomaco smooth the way for new NY State concrete highway
    April 2, 2014
    When New York State Thruway wanted to experiment with unbonded concrete overlays, they chose an 8km, four-lane section of Interstate 90 near Hamburg as their test section. Surianello General Concrete, based in Buffalo, New York, won the bid to pave the 22.9cm thick concrete overlay. The age and the design of the original roadway created a major paving challenge. It was built in the 1950s and didn’t conform to current geometry requirements for superhighways. “They built it with a standard crown sectio
    Read More

Highlighted Content