Precision pothole patching from Bergkamp’s Pivot Tack System

Tack that is sprayed into potholes to increase adhesion within a patch can also adhere to your equipment hoses. In addition, the hoses can present jobsite tripping hazards. To address these common issues, Bergkamp has engineered a Pivot Tack/Air Hose System for its FP5 Flameless All-In-One Pothole Patcher. Located at the back-right side of the FP5’s hopper body, the system’s pivoting arm holds the original tack hose off of the ground and parallel to the hopper, locked in place for transporting with a spr
May 9, 2019 Read time: 2 mins
Blameless with the FP5 Flameless: Bergkamp’s Pivot Tack System keeps tack off of equipment and in the pothole thanks to an extending hose arm support

Tack that is sprayed into potholes to increase adhesion within a patch can also adhere to your equipment hoses. In addition, the hoses can present jobsite tripping hazards. To address these common issues, 3850 Bergkamp has engineered a Pivot Tack/Air Hose System for its FP5 Flameless All-In-One Pothole Patcher.

Located at the back-right side of the FP5’s hopper body, the system’s pivoting arm holds the original tack hose off of the ground and parallel to the hopper, locked in place for transporting with a spring-loaded pin. When in use, the pivot arm also locks into position, allowing the operator to keep the hose suspended and off of the ground. This eliminates a trip hazard, as well as the chance of dragging the hose through wet tack.

The pivot arm and hose system has a 180° pivot capability and provides just over 6m of overall extended reach with the tack wand. A retrofit Pivot Tack/Air Hose System can be mounted on existing FP5 Pothole Patchers.

The updated Pivot Tack/Air Hose System is one of the many ways in which Bergkamp says that its FP5 All-In-One Pothole Patcher not only carries all of the necessary equipment needed for a full day of pothole repair work, but allows a crew to work safely and efficiently.

Bergkamp is a global company based in Salinas, in the US state of Kansas. The company has been manufacturing truck-mounted, trailer-mounted and continuous slurry seal and micro surfacing pavers and equipment, as well as spray injection and pothole patching equipment since 1977.

Asphalt milling, paving & compaction

For more information on companies in this article

Related Content

  • Seal of approval
    August 2, 2012
    Timely maintenance using proven cost-effective methods can extend the life of a highway by many years as Patrick smith reports Highways are expensive assets to construct, and the wear and tear of modern traffic means that regular maintenance will delay costly repairs or in extreme cases reconstruction. There are a number of methods of carrying out such maintenance, and these include the use of slurry seals and micro-surfacing, which are cold mixed asphalt which is a mixture of graded aggregate, asphalt emul
    Read More
  • Grand achievement for Intermountain
    July 18, 2012
    A versatile solution has helped with a tricky project at the Grand Canyon in the US – Pierre Peltier When Intermountain Slurry Seal, a division of Granite Construction, submitted its bid in 2009 to repair roads and parking lots along the Grand Canyon’s North Rim, the company knew the job would come with challenges. The remote roads leading from Jacob’s Lake, Arizona, to the North Rim Lodge had deteriorated to a point that the Federal Highway Association’s (FHWA) Central Federal Lands (CFL) Highway Division
    Read More
  • Electronic controls bring efficiency to Bergkamp’s micro surfacing paver
    March 6, 2014
    Bergkamp has launched the M1E self-propelled continuous slurry seal and micro surfacing paver. The machine has two main advantages over older versions, said the manufacturer: it is easier to operate and has electronic mix control and diagnostics. “It is much simpler to operate than the old-style machine,” said Bergkamp general manager Bill Cooper. “The operator can pick it up much quicker which means that if you lose an operator you can get a new one up to speed faster.”
    Read More
  • Electronic controls bring efficiency to Bergkamp’s micro surfacing paver
    January 6, 2017
    Bergkamp has launched the M1E self-propelled continuous slurry seal and micro surfacing paver. The machine has two main advantages over older versions, said the manufacturer: it is easier to operate and has electronic mix control and diagnostics. “It is much simpler to operate than the old-style machine,” said Bergkamp general manager Bill Cooper. “The operator can pick it up much quicker which means that if you lose an operator you can get a new one up to speed faster.”
    Read More

Highlighted Content