Hamburg-Finkenwerder airport has new runway surface

Hamburg’s Finkenwerder airport is now benefiting from a new runway surface following work carried out by contractor KEMNA BAU. The company recently used machines from Dynapac to resurface 36,000m2 of the runway track in Hamburg-Finkenwerder, a facility used by Airbus. The airport handles around 10-15 take-offs and landings/day when aircraft are either undergoing flight testing or being delivered to customers, as well as for deliveries of components by transport aircraft. The project was tricky as the
August 21, 2013 Read time: 3 mins
The contractor had to pave 36,000m2 within a short time frame using the Dynapac pavers and materials feeders

Hamburg’s Finkenwerder airport is now benefiting from a new runway surface following work carried out by contractor KEMNA BAU.

The company recently used machines from 206 Dynapac to resurface 36,000m2 of the runway track in Hamburg-Finkenwerder, a facility used by Airbus. The airport handles around 10-15 take-offs and landings/day when aircraft are either undergoing flight testing or being delivered to customers, as well as for deliveries of components by transport aircraft.

The project was tricky as the contractor had just four days in which to carry out the resurfacing so as to avoid impinging on air traffic. In this short time slot, the firm had to mill out the old asphalt surface down to the original binder course and then repave this with new asphalt. In addition, the contractor was also responsible for the subsequent application of the markings.

To meet the tight time schedule, the contractor used machines working together. Three Dynapac pavers were brought to the site along with Dynapac material feeders to meet the high surface requirements stipulated by the aircraft manufacturer Airbus. The three SD2550CS pavers were set up with R300 TV rigid screeds that were 12m wide. “In order to progress as quickly as possible, we decided to use two staggered machine units, consisting of a paver and a feeder,“  Henning Peter from KEMNA BAU explained. In case of any problems with the equipment, the third Dynapac paver and materials feeder were near at hand on standby.
The firm used the latest version of the MF2500 CS feeder with its short conveyor, which was launched at the 688 Bauma 2013 exhibition a few months ago. The contractor also used the new MF2500 CL version of the feeder with its long conveyor and

both machines worked reliably, with the standby units not being required in the end. As the two pavers were used alongside each other, they were also able to lay the surface with a hot-to-hot joint, which allowed a better bond and will contribute to a longer working life, as well as improving surface quality.

The contractor was able to use the machines to pave the surface and meet the tight quality requirements of the client. The specification stated that the new asphalt surface would not deviate more than +/-0.2% from the desired slope, while unevenness to be a maximum of 3mm over a 4m long test section.
Asphalt milling, paving & compaction

For more information on companies in this article

Related Content

  • Russian quarry increases efficiency with Sandvik equipment
    August 20, 2015
    A quarry facility in Russia has increased working efficiency by using Sandvik machinery. Located in in the Kurgan Region (Urals) of Russia, the Sinarsky Quarry is benefiting from an increase in throughput and reduced downtime since its new Sandvik crushing and screening plant became fully operational. The company invested over €2 million on the new plant, and is aiming to use it in order to double its aggregates production. This increase in production is required in order to meet the doubling of demand for
    Read More
  • Better road surfaces to last longer
    August 23, 2013
    Preservation can make roads perform better and last longer - and save money in the long run. Kristina Smith reports BAM Wegen has laid the first ever half-warm porous asphalt section on a major highway in the Netherlands. The asphalt for the 500m-long test section on the A18 near Varsseveld was produced at 105°C rather than 160°C, representing a saving on energy and CO2 emissions of around 30%.
    Read More
  • Technology makes materials testing quicker and easier
    February 14, 2012
    Sophisticated technology is now being used to make the testing of a wide variety of materials quicker and easier as Patrick Smith reports. Ever since the CE mark became mandatory for asphalt mixes, it also became necessary and important to update the testing equipment and systems used for testing such materials.
    Read More
  • Asphalt plant technology meets market needs
    February 16, 2012
    Plants for mixing asphalt are becoming more sophisticated than ever, while users are looking for ecological and technological benefits. Patrick Smith reports. When the Adige Bitumi Group decided to renew its old M 260 plant it chose to collaborate with Marini for the design and development of a plant with production of 280-300tonnes/hour.
    Read More

Highlighted Content