Geosynthetics stabilise differential settlement

The ongoing Highways Agency A66 Carkin Moor to Scotch Corner project involves upgrading the original single carriageway to address safety concerns, particularly at junctions and crossings. Where differential settlement is threatening a remodelled junction, Tensar International's new TriAx geogrid provides an additional dimension of stability, saving design and build contractors Balfour Beatty Regional Civil Engineering Limited (BBRCEL) the heavy time and costs inherent in conventional remedial solutions and
May 3, 2012 Read time: 3 mins
Inbitex has been developed to enhance the performance of Formpave's Aquaflow permeable paving system

The ongoing Highways Agency A66 Carkin Moor to Scotch Corner project involves upgrading the original single carriageway to address safety concerns, particularly at junctions and crossings.

Where differential settlement is threatening a remodelled junction, 340 Tensar International's new TriAx geogrid provides an additional dimension of stability, saving design and build contractors 1146 Balfour Beatty Regional Civil Engineering Limited (BBRCEL) the heavy time and costs inherent in conventional remedial solutions and meeting the 1441 UK Highways Agency's (HA) key performance indicators.

The widened junction incorporates radiused corners on 'turn in' and 'turn out', and overlies part of a 7m deep old quarry variably infilled with very poor quality mixed domestic waste. The original proposals by BBRCEL's design partner 3005 Atkins included excavation, disposal and replacing it with high quality imported fill, which would have cost hundreds of thousands of pounds and would have been environmentally undesirable.

With the encouragement of the HA to look at innovative solutions to manage costs more effectively and reduce environmental impact, BBCREL and Atkins consulted Tensar about geogrid solutions.

A specific concern of the project was that one leg of the junction runs over the irregular edge of the quarry, with very variable direction of potential instability while, at the same point, vehicle wheel loadings are also going to be variable in direction.

To meet this problem, Tensar proposed use of its new TriAx geogrid, as a composite structure including granular fill and heavy duty bi-axial geogrid at the base to create a reinforced granular mattress.

Says Sean McCready, site project manager for BBRCEL: "The innovative TriAx solution offers excellent cost benefits of at least 75% savings to the project against very acceptable risk levels. This approach also fulfilled the HA's objective of looking at innovative proven solutions to drive down cost. We talked this through with 2377 Mouchel Parkman, who are charged with the HA's supervision of the works, as well as Atkins, to come to a joint decision." The TriAx structural solution is said to not only eliminate the cost, time and excessive transportation required for the excavation proposals but also minimise the undesirable environmental impact of large quantities of landfill disposal, high quality aggregate extraction and vehicle journeys.

Inbitex development

In a recent partnership between Terram and Formpave, the specialist geotextile Inbitex has been developed to enhance the performance of Formpave's Aquaflow permeable paving system.

Research conducted by Coventry University in the UK identified the need for an improved geotextile during the installation of the sub-base of the paving system.

Inbitex was the new geotextile developed in conjunction with Terram, creating a product of greater quality and strength: importantly the fibres of the geotextile encourage the growth of a microbic biofilm habitat. These microbes biodegrade any organic matter found in the run-off, with a capacity to consume 400g of hydrocarbon/year. Also, any non-degradable matter such as heavy metals and silts are trapped in the laying course, so optimising the cleansing of water entering the Aquaflow paving system.

A typical infiltration system in the Aquaflow paving system installation uses two permeable Inbitex geotextiles, one beneath the base of the paving and the other beneath the sub-base or lower sub-base
Asphalt milling, paving & compaction

For more information on companies in this article

Related Content

  • Geosynthetic solution for ground preparation
    April 16, 2012
    Naue Geosynthetics says its Secugrid offers a solution for a host of ground preparation problems, and for use in reinforced retaining walls. Secugrid is a geogrid made from extruded monolithic flat bars with welded junctions, for soil reinforcement in earth, landfill and road construction as well as in hydraulic engineering applications. Among its benefits are said to be its high strength and low elongation thanks to the extruded elements. "The monolithic flat bars give it a robust construction, an
    Read More
  • Geosynthetics for base reinforcement
    March 14, 2012
    Tensar is making some key moves internationally, as well as in terms of market segments. The company is now marketing the GlasGrid range in the US and expects to develop healthy sales, however it sees major growth potential with the Geogrid product range. Jim Penman, director for bi-axial products & applications said: "One area we're moving into is base reinforcement and in particular what we're looking at is mechanistic emirical (ME) technology." Tensar has worked with the University of Illinois on a new d
    Read More
  • Importance of road/tunnel drainage systems
    April 10, 2012
    A variety of systems are available for quickly and efficiently removing water from roads as Patrick Smith reports The presence of water in a highway layer reduces the bearing capacity of the road, and in doing so it also reduces the structure's lifetime. Indeed, the recent extremely cold winter in many parts of Europe has shown that in colder climates there is a risk of frost damage when water is present resulting in costly potholes, so drainage systems performing properly are important in road design.
    Read More
  • Importance of road/tunnel drainage systems
    May 8, 2012
    A variety of systems are available for quickly and efficiently removing water from roads as Patrick Smith reports. The presence of water in a highway layer reduces the bearing capacity of the road, and in doing so it also reduces the structure's lifetime. Indeed, the recent extremely cold winter in many parts of Europe has shown that in colder climates there is a risk of frost damage when water is present resulting in costly potholes, so drainage systems performing properly are important in road design.
    Read More

Highlighted Content