Improved airport for Thimarafushi atoll

Thimarafushi forms part of the Thaa Atoll lying in the Indian Ocean but access has been limited in the past. However the construction of a new airport planned by the Maldives Government will help develop the tourist trade, boosting the local economy. Most visitors previously used the country’s two international airports, using these as hubs for flights to the country’s six domestic airports. This has limited travel to only a few of the country’s 1,192 islands, of which around 200 are inhabited. As a result,
August 29, 2014 Read time: 3 mins
Caterpillar machines provide new runway surface on Thaa Atoll
RSS

Thimarafushi forms part of the Thaa Atoll lying in the Indian Ocean but access has been limited in the past

However the construction of a new airport planned by the Maldives Government will help develop the tourist trade, boosting the local economy. Most visitors previously used the country’s two international airports, using these as hubs for flights to the country’s six domestic airports. This has limited travel to only a few of the country’s 1,192 islands, of which around 200 are inhabited. As a result, reaching most of the islands requires travel by boat.

A few years ago, the Maldives Government began to build its seventh domestic airport, on the island of Thimarafushi. The scenic island was chosen because of its natural beauty, and also because it could serve as a hub for those wanting to travel by boat to other nearby islands.

Maldives Transport and Contracting Co (MTCC), a customer of 4018 Caterpillar Paving dealer Tractors Singapore Limited, was awarded the contract to develop the Thimarafushi Airport in May 2012. The project began with 31ha of land being reclaimed both for the construction of the airport and to provide adequate housing for the islanders. The reclamation portion of the airport project was completed in 2011. Project plans called for a 1200m long by 30m wide runway and taxiway, with an asphalt surface. MTCC used a fleet of Cat equipment through most phases of the project, including a CS533E soil compactor, AP655D asphalt paver, CB434D vibratory asphalt compactor, CW34 pneumatic compactor, 336D L hydraulic excavator, M313C wheeled hydraulic excavator, 120K grader and 924Gz wheeled loader.

Logistics posed a challenge as the equipment had to be delivered by landing craft and barge, which included the hot mix plant, which was transported in pieces. Operators, too, were hard to find. Tractors Singapore Limited provided training to the customer and operators before the project started. During the building of the runway, a Tractors Singapore Limited product application expert and an engineer visited the jobsite to provide assistance. But even their travel was difficult. First, they had to fly to a nearby atoll, and then use sea transportation. It took about a half day of travel to reach Thimarafushi from one of the country’s two international airports.


The runway is surrounded by sea on the reclaimed land. Site preparation included the placement and compaction of aggregate. Project specifications required that 100% compaction densities were achieved on four layers.

A 200mm sub-base was placed first, and the Cat CS533E compacted it to 150mm. The same process was followed for the second layer. The third layer consisted of binding material that was placed at 130mm and compacted to 100mm.

The fourth layer was asphalt with aggregates of 12.5mm, 9mm and 6mm. It was placed at 60mm and compacted to 50mm. A Cat AP655D asphalt paver with AS4251 screed handled the paving.

Paving production was limited because of the hot mix plant’s capacity of 45tonnes. During the average day, the paver placed a strip that was 5m wide and 700m long. Dump trucks hauled the mix the short distance from the plant to the runway.

RSS
Earthmoving & soil compaction Asphalt milling, paving & compaction

For more information on companies in this article

Related Content

  • Oscillation compaction advance in the US
    October 2, 2018
    A project carried out by LYNCH, one of the leading contractors in the south-east of New England, provided for the placement and compaction of asphalt on a road near Douglas, MA. A BOMAG BW 190 ADO-5 was used on the 3km section being redeveloped; this was assigned to work on the 60mm thick asphalt binder course and the 25mm thick top layer. The special feature of the project was in the application of the WMA process (Warm Mix Asphalt – low-temperature asphalt). In the course of this process, additive is add
    Read More
  • Sand and gravel production in Bavaria
    September 14, 2015
    Sand and gravel productions operations in Bavaria are benefiting from new equipment that is helping boost output. Having recently commissioned a Sennebogen 640 HD crawler crane, Hans Wolf is using its machine equipped with a dragline bucket for gravel extraction. The machine was supplied from Sennebogen’s plant, also in Straubing, and was purchased following a successful trial at the site. The Hans Wolf group is based in Straubing and has a network of gravel plants and transport companies in Lower Bavari
    Read More
  • The MF2500CS IMIX - Combining high quality results with low cost of ownership
    May 1, 2021

    The logistics and the mixing plant locations vary on every jobsite. Whenever the travelled distance of the asphalt trucks is long or the roads are wavy, segregation in the asphalt bellies of the trucks cannot be avoided.

    IMIX equalizes temperatures within the mix and blends large and small size aggregates to avoid segregated sections in the asphalt mat. Homogenous sections ensure uniform density of compaction and increase the lifetime of the road.

    Read More
  • Low energy asphalt helps reduce impact on environment
    July 11, 2012
    Petroplus Bitumen has been awarded the sole UK licence for the Low Energy Asphalt (LEA) franchise, and as exclusive distributor will promote how the technology can help to reduce the environmental impact of highways construction and maintenance in the UK. It offers asphalt manufacturers the opportunity to reduce their carbon footprints by achieving up to 50% energy and emission savings, while maintaining the appearance and performance of conventional asphalt. LEA involves the manufacture and laying of aspha
    Read More

Highlighted Content