Improved airport for Thimarafushi atoll

Thimarafushi forms part of the Thaa Atoll lying in the Indian Ocean but access has been limited in the past. However the construction of a new airport planned by the Maldives Government will help develop the tourist trade, boosting the local economy. Most visitors previously used the country’s two international airports, using these as hubs for flights to the country’s six domestic airports. This has limited travel to only a few of the country’s 1,192 islands, of which around 200 are inhabited. As a result,
August 29, 2014 Read time: 3 mins
Caterpillar machines provide new runway surface on Thaa Atoll
RSS

Thimarafushi forms part of the Thaa Atoll lying in the Indian Ocean but access has been limited in the past

However the construction of a new airport planned by the Maldives Government will help develop the tourist trade, boosting the local economy. Most visitors previously used the country’s two international airports, using these as hubs for flights to the country’s six domestic airports. This has limited travel to only a few of the country’s 1,192 islands, of which around 200 are inhabited. As a result, reaching most of the islands requires travel by boat.

A few years ago, the Maldives Government began to build its seventh domestic airport, on the island of Thimarafushi. The scenic island was chosen because of its natural beauty, and also because it could serve as a hub for those wanting to travel by boat to other nearby islands.

Maldives Transport and Contracting Co (MTCC), a customer of 4018 Caterpillar Paving dealer Tractors Singapore Limited, was awarded the contract to develop the Thimarafushi Airport in May 2012. The project began with 31ha of land being reclaimed both for the construction of the airport and to provide adequate housing for the islanders. The reclamation portion of the airport project was completed in 2011. Project plans called for a 1200m long by 30m wide runway and taxiway, with an asphalt surface. MTCC used a fleet of Cat equipment through most phases of the project, including a CS533E soil compactor, AP655D asphalt paver, CB434D vibratory asphalt compactor, CW34 pneumatic compactor, 336D L hydraulic excavator, M313C wheeled hydraulic excavator, 120K grader and 924Gz wheeled loader.

Logistics posed a challenge as the equipment had to be delivered by landing craft and barge, which included the hot mix plant, which was transported in pieces. Operators, too, were hard to find. Tractors Singapore Limited provided training to the customer and operators before the project started. During the building of the runway, a Tractors Singapore Limited product application expert and an engineer visited the jobsite to provide assistance. But even their travel was difficult. First, they had to fly to a nearby atoll, and then use sea transportation. It took about a half day of travel to reach Thimarafushi from one of the country’s two international airports.


The runway is surrounded by sea on the reclaimed land. Site preparation included the placement and compaction of aggregate. Project specifications required that 100% compaction densities were achieved on four layers.

A 200mm sub-base was placed first, and the Cat CS533E compacted it to 150mm. The same process was followed for the second layer. The third layer consisted of binding material that was placed at 130mm and compacted to 100mm.

The fourth layer was asphalt with aggregates of 12.5mm, 9mm and 6mm. It was placed at 60mm and compacted to 50mm. A Cat AP655D asphalt paver with AS4251 screed handled the paving.

Paving production was limited because of the hot mix plant’s capacity of 45tonnes. During the average day, the paver placed a strip that was 5m wide and 700m long. Dump trucks hauled the mix the short distance from the plant to the runway.

RSS
Earthmoving & soil compaction Asphalt milling, paving & compaction

For more information on companies in this article

Related Content

  • Multiple milling machines removing surface
    April 24, 2019
    Milling subcontractor Pavement Recycling Systems removed thousands of tonnes of reclaimed asphalt pavement (RAP) from a runway at Oakland International Airport in California recently. The firm used a fleet of six Wirtgen W 210i cold milling machines to remove the asphalt in less than 60 hours from Runway 12-30, along the shore of San Francisco Bay. In total, 47,000tons of asphalt were milled within a 60-hour time frame, nonstop day and night, plus a single-shift second phase a week later. The firm start
    Read More
  • Upgrades to Fort McMurray airport will aid Canada’s oil industry
    August 21, 2013
    Canada’s vast tar sands operation is providing a major financial boost to the country and this industry has relied heavily on Fort McMurray airport. Situated in Alberta, Fort McMurray is a remote town that has seen a huge expansion following the upturn in activity in the tar sands operations nearby. Although the massive resource has been worked for decades, only in the last 15 years or so have new extraction methods made the operation truly economic. Since 2010 Fort McMurray’s population has increas
    Read More
  • Arizona Chemical study reveals lower CO2 footprint with RAP additive
    May 18, 2015
    A life-cycle assessment has found that an asphalt mix containing a high percentage of reclaimed asphalt pavement (RAP) along with an additive by Arizona Chemical can produce a significantly lower carbon footprint than virgin asphalt mix or a mix containing a low percentage of RAP. The assessment study was carried out by third party Arthur D. Little, an international management consulting firm, using Arizona Chemical’s SYLVAROAD RP 1000 performance additive. The work noted that cradle-to-gate, a road aspha
    Read More
  • Competitive asphalt compaction market
    February 13, 2012
    Existing tough competition will step up another gear with the launch of further new machines in the asphalt roller market, Mike Woof reports. The asphalt compaction equipment market is intensely competitive, with a number of major firms all fighting to boost market share. And with many major manufacturers having revamped ranges during 2010 and further new models now due, this rivalry is set to become tougher still.
    Read More

Highlighted Content