Curtains for speeders at Curtin University thanks to Actibump

Curtin University in Perth, Australia, is rolling out more Actibumps for slowing traffic after what is says has been a successful trial of four systems. “We expected the same effect as in Sweden,” said David Eskilsson, general manager at Edeva, the Actibump manufacturer based in Linkoping. “But the decrease in the percentage of speeding drivers from over 70% of all drivers in January to below 25% in October last year on the most difficult site has been better than even we expected.” In January 2018 Curtin
June 10, 2019 Read time: 3 mins
Actibump successful in Australia
Curtin University in Perth, Australia, is rolling out more Actibumps for slowing traffic after what is says has been a successful trial of four systems.


“We expected the same effect as in Sweden,” said David Eskilsson, general manager at 5190 Edeva, the Actibump manufacturer based in Linkoping. “But the decrease in the percentage of speeding drivers from over 70% of all drivers in January to below 25% in October last year on the most difficult site has been better than even we expected.”

In January 2018 Curtin University installed four of the active speed bumps to reduce the number of speeding drivers, particularly on semester week days when there are a lot of pedestrians and vehicles on campus. Each day around 2,000 vehicles use the street which has a speed limit of 40km/h.

“The use of the smart speed bumps also provides a steadier flow of traffic, which makes it easier for pedestrians to judge the speed of the approaching vehicle,” said Graham Arndt, director of operations and maintenance at Curtin University. “Additionally, the units have been maintenance free and operated continuously for a year without the need for any intervention.”

Arndt said the university will be installing another set of two active speed bumps on Townsing Drive and another active speed bump will replace a so-called dumb bump - a moulded black plastic bump near the Manning Road entrance. The Actibump traffic safety system allows full accessibility for all vehicles driven at, or under, the set speed limit. Speeding vehicles are physically reminded of the speed limit by an inverted speedbump. A radar measures the speed of the oncoming vehicles and speeding vehicles activate a hatch that is lowered a few centimetres into the road surface. Drivers were surprised to see the road “disappear in front of them” and this made them slow down, said Arndt.

For non-speeders the hatch remains level with the road surface. Edeva says that  independent evaluations have shown that the system decreases the noise, improves yielding behaviour and decreases the speed to that of the speed limit of around 3km/h, regardless of speed limit or previous speeding behaviour.

Speed limit and other variables are set through a web-based interface that also presents the statistics collected by the system.

Edeva says that around 50 Actibump units have been installed worldwide, with most of them in Sweden including in Linköping, Malmö, Helsingborg, Karlstad and two of them are installed in Ystad, on the European road network E65 owned by the Swedish Transport Administration.

Highway & Network Management

For more information on companies in this article

Related Content

  • ACE/AECOM report: private sector and user-pay for English roads
    May 14, 2018
    It’s one minute to midnight for funding England’s roads, according to a timely new report, and the clock’s big hand is pointing to some form of user-pay solution, reports David Arminas Is there any way out of future user-pay funding for England’s highway infrastructure? The answer is a resounding ‘no’, according to the recently published report: Funding Roads for the Future. The brief 25-page document by the London-based Association for Consultancy and Engineering, ACE**, sums up the state of England’s ro
    Read More
  • Asphalt milling optimised by 3D controls
    February 20, 2012
    3D machine controls can optimise milling efficiency, Mike Woof reports. More efficient milling and recycling operations can be carried out by using the latest 3D control systems on the market. At the last Trimble Dimensions event in Las Vegas, the advantages of 3D controls for milling operations proved a key topic. The use of 3D control systems can offer huge advantages in milling operations. This technology helps increase productivity as the milling machine will only remove what is required, which also hel
    Read More
  • Weighty matters for developing countries
    November 6, 2012
    One leading Weigh in Motion technology manufacturer is helping governments in developing countries reduce excessive road damage, while several others have seen their latest WIM systems recently used on the highways of Eastern Europe. Guy Woodford reports Recent Central Weighing WIM installations in Bangladesh are helping its national government reduce the financial burden of excessive road damage, while also protecting many bridges that are vital to transport and trade. The need for such installations was e
    Read More
  • Growing WIM demand in Russia and South America
    April 4, 2014
    One Eastern European WIM manufacturer is finding commercial success in Russia, while another leading manufacturer is in demand in South America, as Guy Woodford reports Since Czech WIM technology manufacturer Camea secured type approval for its UnicamWIM system in early 2013, the firm has been installing a number of the systems in different Russian regions. These have included two UnicamWIM stations in Novosibirsk, one in the Kostroma region, and another on the M20 Highway between Belarus and Russia.
    Read More

Highlighted Content