Curtains for speeders at Curtin University thanks to Actibump

Curtin University in Perth, Australia, is rolling out more Actibumps for slowing traffic after what is says has been a successful trial of four systems. “We expected the same effect as in Sweden,” said David Eskilsson, general manager at Edeva, the Actibump manufacturer based in Linkoping. “But the decrease in the percentage of speeding drivers from over 70% of all drivers in January to below 25% in October last year on the most difficult site has been better than even we expected.” In January 2018 Curtin
June 10, 2019 Read time: 3 mins
Actibump successful in Australia
Curtin University in Perth, Australia, is rolling out more Actibumps for slowing traffic after what is says has been a successful trial of four systems.


“We expected the same effect as in Sweden,” said David Eskilsson, general manager at 5190 Edeva, the Actibump manufacturer based in Linkoping. “But the decrease in the percentage of speeding drivers from over 70% of all drivers in January to below 25% in October last year on the most difficult site has been better than even we expected.”

In January 2018 Curtin University installed four of the active speed bumps to reduce the number of speeding drivers, particularly on semester week days when there are a lot of pedestrians and vehicles on campus. Each day around 2,000 vehicles use the street which has a speed limit of 40km/h.

“The use of the smart speed bumps also provides a steadier flow of traffic, which makes it easier for pedestrians to judge the speed of the approaching vehicle,” said Graham Arndt, director of operations and maintenance at Curtin University. “Additionally, the units have been maintenance free and operated continuously for a year without the need for any intervention.”

Arndt said the university will be installing another set of two active speed bumps on Townsing Drive and another active speed bump will replace a so-called dumb bump - a moulded black plastic bump near the Manning Road entrance. The Actibump traffic safety system allows full accessibility for all vehicles driven at, or under, the set speed limit. Speeding vehicles are physically reminded of the speed limit by an inverted speedbump. A radar measures the speed of the oncoming vehicles and speeding vehicles activate a hatch that is lowered a few centimetres into the road surface. Drivers were surprised to see the road “disappear in front of them” and this made them slow down, said Arndt.

For non-speeders the hatch remains level with the road surface. Edeva says that  independent evaluations have shown that the system decreases the noise, improves yielding behaviour and decreases the speed to that of the speed limit of around 3km/h, regardless of speed limit or previous speeding behaviour.

Speed limit and other variables are set through a web-based interface that also presents the statistics collected by the system.

Edeva says that around 50 Actibump units have been installed worldwide, with most of them in Sweden including in Linköping, Malmö, Helsingborg, Karlstad and two of them are installed in Ystad, on the European road network E65 owned by the Swedish Transport Administration.

Highway & Network Management

For more information on companies in this article

Related Content

  • Skidmarks: Scaring speeders
    February 6, 2020
    Our Skidmarks page is highly rated by readers. Your input could help make this page even more entertaining. If you come across any amusing road-related stories or pictures email me at [email protected]
    Read More
  • Swarco signs for slower Swansea speed limit
    June 30, 2023
    In March, the Welsh government passed a law which from September will see the default speed limit on restricted roads in Wales reduced from 30mph (50kph) to 20mph (32kph).
    Read More
  • Researchers trial 3D printing for both concrete and asphalt roads
    February 27, 2019
    Automated road repairs, using 3D printing, could save money and vastly reduce disruption, and researchers are already showing it’s possible - Kristina Smith reports It’s the middle of the night, and in the street below a team is busy carrying out repairs to the road surface. But there isn’t a human in sight. A road repair drone has landed at the site of a crack and a 3D asphalt printer is now busy filling in that crack. A group of traffic cone drones have positioned themselves around the repair location
    Read More
  • Self-healing roads, slippery roads and slimmer roads
    November 24, 2017
    This month’s bitumen technology pages bring you self-healing roads, slippery roads and slimmer roads and explains why one UK contractor has started manufacturing its own polymer modified bitumen - Kristina Smith reports. Professor Erik Schlangen, who heads up experimental micromechanics at the Delft University of Technology is receiving calls from all round the world these days. And it is hardly surprising because he and his team have invented a great new technology: asphalt that heals itself.
    Read More

Highlighted Content