Skip to main content

Norsenga Bridge undergoes weathering tests

Norway’s Statens Vegvesen says the wooden truss bridge – opened only in 2017 – will be the subject of a study in conjunction with the Norwegian University of Science and Technology.
By David Arminas May 19, 2023 Read time: 2 mins
The two-lane Norsenga Bridge, nearly 95m long, was opened in 2017 and has walking and cycling paths (image © Jørn Jakobsen, Norwegian Road Administration)

Statens Vegvesen says it is studying the impact of moisture and temperature on the Norsenga Bridge, one of 14 wooden truss bridges closed last year.

The bridges are on the E16 in Kongsvinger, near Oslo, which were closed after the wooden bridge at Tretten collapsed in August 2022. According to Statens Vegvesen, humidity and temperature may be affecting the load capacity of the bridge, which was reopened last September, but only to one-way traffic.

The study on one of the most is being done in conjunction with the Norwegian University of Science and Technology (NTNU).

According to Statens Vegvesen, the Norsenga Bridge is a priority structure because it has the most traffic of all the 14 bridges that were closed immediately after the collapse of the Tretten Bridge in 2022. The 150m-long, 10m-wide Tretten Bridge - only a decade old - broke in two, collapsing into the river, stranding two vehicles and their occupants. There were no casualties or injuries in the early morning accident on August 15, but one driver was airlifted to safety.

When the bridge was reopened last September, Statens assured the public the bridge is safe for traffic. But as a cautionary measure, it reduced the load by closing one of the two lanes. The bridge was reopened only after rigorous third-party inspections, said the administration.

The two-lane Norsenga Bridge, nearly 95m long, was opened in 2017 and has walking and cycling paths. It is divided into three spans and sits on pointed concrete piles, according to Nordic Steel Group which supplied material for the trusses. Around 710m³ glulam were supplied by Moelven for the construction and truss. In total, the Norsenga bridge weighs over 400 tonnes, divided into both wood and steel.  It required 66tonnes of black steel and 70tonnes of Duplex in the delivery. Five of the transverse carriers are in black steel and four in the Duplex - these weigh between 6tonnes and 10tonnes each.

The massive glulam structures are interconnected with slit plates at the ends of the glulam beams. Slit fittings enable massive wood screws to keep the construction in place. Large bridge carriers in acid-resistant steel secure the structures.

For more information on companies in this article

Related Content

  • Pearl Harbor Memorial Bridge, an extradosed design, opens in Connecticut
    September 30, 2015
    The first extradosed designed bridge in the United States, the Pearl Harbor Memorial Bridge in New Haven, Connecticut, was opened to traffic on September 28.
  • Us bridges pose cause for concern
    August 2, 2017
    On Aug 1st 2017, it was 10 years since the I-35W Bridge in Minneapolis collapsed. The bridge had been classified as structurally deficient and was undergoing repair at the time. However the repairs focussed on the decking rather than the structure, with the additional weight of the extra asphalt layers and the construction machinery parked adding to the total load and contributing to the collapse.
  • Norway’s E18 Lysaker-to-Ramstadsletta project faces funding issue
    December 20, 2018
    A lack of financing is jeopardising construction of the new E18 highway between Lysaker and Asker on the outskirts of Oslo. Media reports say that the Norwegian Road Administration (Statens Vegvesen) has received no funding for the project that is scheduled to start next year. The first phase of the project, between Lysaker and Ramstadsletta, has been scheduled for 2019-2024. Around 90,000 vehicles use the existing E18 road, a local thoroughfare. The new E18 will include cycle paths, pedestrian ways a
  • New German autobahn bridge under constriuction
    May 1, 2015
    Crane manufacturer Manitowoc has supplied six Potain cranes to German contractor Max Bögl. These machines are being used for constructing a new bridge carrying the A3 autobahn, close to Limburg. Working at over 70m high, the cranes tower over the Lahn Valley. The cranes for this project were supplied by Max Bögl’s subsidiary, Max Bögl Transport & Geräte. The three topless Potain MDT 222 cranes were selected for the work as they feature tip heights of up to 76.2m and can operate with a working radius of