Mählers launches the SOP-LB2800 sweeper for trucks and wheel loaders

Mählers, best known globally for its snow ploughs, has broadened its range of attachments with the addition of a vehicle-mounted hydraulic rotating sweeper. The SOP-LB2800 sweeper is intended for use on trucks and wheel loaders and features an "active" float mode to give balanced pressure on the ground and especially when following contours of the road surface. Active float gives the right brush pressure evenly across its full width, regardless of its position relative to the host vehicle. This also c
July 16, 2019 Read time: 2 mins
The SOP-LB2800 sweeper features an "active" float mode

Mählers, best known globally for its snow ploughs, has broadened its range of attachments with the addition of a vehicle-mounted hydraulic rotating sweeper.

The SOP-LB2800 sweeper is intended for use on trucks and wheel loaders and features an "active" float mode to give balanced pressure on the ground and especially when following contours of the road surface.

Active float gives the right brush pressure evenly across its full width, regardless of its position relative to the host vehicle. This also contributes to increased bristle lifetime, explains Oscar Nyberg, a designer at Mählers and who helped develop the sweeper.

The LB2800 sweeper can swivel through ± 35º and can be equipped with lateral displacement and irrigation with separate water tank. The sweeper is designed for easy maintenance and the brush-rings can be quickly replaced by hand, according to the company.

Brush width (straight) is 2800mm while the minimum brushing width is 2350mm. Circumference of the brush rings is 915mm and hydraulic flow is between 40-80 litres per minute.

For transportation the SOP-LB2800 sweeper weighs in at 850kg with a minimum transport width of 3025mm. Ground clearance at maximum lift 200mm.

The company, based in Rossön, Sweden, unveiled the SOP-LB2800 at this year's Maskin-Expo for machinery in Stockholm, Sweden, in May.

Road Markings, Barriers & Workzone Protection

Related Content

  • Underground routes for highways
    July 20, 2012
    Increasingly, and where possible, roads are being built in tunnels often for environmental reasons, writes Patrick Smith As part of the new M7 motorway development in the southwest of Ireland, the four-lane route crosses the River Shannon near Limerick, before it flows into the Atlantic. Centrepiece of the 10km long Limerick Southern Ring Road is the required tunnelling (675m long), which including the north and south entrance and exit ramps, means it will be 915m long. Completion of the work is planned for
    Read More
  • Strabag on the edge with a Dynapac DF145CS paver from Atlas Copco
    June 10, 2015
    When asphalting the inside of the newly raised edge of a water dam, Austrian road construction company Strabag faced a challenge. The paver had to be operated at an angle of between 34-41 degrees with material fed into the hopper from a ledge just 2.8m wide on the edge of the dam. The Waldeck 2 kidney-shaped hydroelectric station is located on a mountaintop about 500m above sea level on Lake Eder in central Germany. The dam, owned by global energy group E.ON, has a perimeter of about 3km. An important pa
    Read More
  • Bitumen technology ideal for road repairs
    July 4, 2012
    Mike Woof discusses some novel developments relating to bitumen In the developed countries of Western Europe there is an increasing shift away from new highway construction to maintaining and rebuilding existing roads. In Germany alone, a network of asphalt roads extending more than 600,000km will have to be maintained or repaired. Highway maintenance techniques do vary between European countries but some commonalities exist. There are techniques that have been sidelined in the last few years but which now
    Read More
  • Atlas Copco launches a range the Essential range of hydraulic breakers
    January 12, 2015
    Atlas Copco has introduced a new range of Essential (ES) hydraulic breaker attachments which the company claims give rental centres and contractors a fast return on investment by simplifying maintenance and operation. The three ES models - ES 60, ES 70 and ES 80 - are very narrow to promote good visibility and handling on work sites for construction, landscaping and renovation, said Kevin Loomis, business line manager for Atlas Copco Construction Equipment. Operators can cut narrow and precise trenches
    Read More

Highlighted Content