Skip to main content

Stronger crash barriers may be needed for heavier trucks

The European Road Federation (ERF) has voiced its concern that roadside barriers in Europe may have to be upgraded According to the ERF, the recent decision of the European Commission to allow cross-border movement of longer and heavier trucks, it is keen to raise awareness of the important implications such a move may have for road barriers. ‘Road safety barriers are designed and tested according to the maximum weight of vehicles circulating on Europe’s roads. The current European Norm (EN 1317) allows for
January 4, 2013 Read time: 4 mins
Italy’s A4 autostrade is a major link in the country and has been widened and modernised but larger trucks could pose future dangers for crossover crashes, with potential results similar to those fatal crashes that have happened in the past

The 1202 European Road Federation (ERF) has voiced its concern that roadside barriers in Europe may have to be upgraded

According to the ERF, the recent decision of the 2465 European Commission to allow cross-border movement of longer and heavier trucks, it is keen to raise awareness of the important implications such a move may have for road barriers.

‘Road safety barriers are designed and tested according to the maximum weight of vehicles circulating on Europe’s roads. The current European Norm (EN 1317) allows for the testing of barriers considering the impact of vehicles up to a maximum of 38tonnes. We are concerned that, should heavier vehicles be allowed to circulate more widely on Europe’s roads, this may have serious implications on the ability of road barriers to protect drivers from their own human mistakes’ explains Christophe Nicodème, Director General of the ERF.

'We do not have an ideological opposition to heavier vehicles', explained Konstandinos Diamandouros, Head of Office at ERF and responsible for the area of road restraint systems. ‘We simply believe that the introduction of heavier vehicles on selected routes should be accompanied by the necessary adaptations to the road infrastructure and this of course includes safety barriers.’

Road restraint systems are designed and tested up to withstand the impact of a maximum 38tonne truck. Given that the current directive in force allows a maximum weight of 44tonnes, even the current barrier requirements do not match the maximum weight of trucks on Europe’s roads.

In the ERF’s opinion, the introduction of heavier vehicles on Europe’s motorways may entail serious safety implication for the ability of passive safety devices to protect drivers. An H4b road restraint system designed for a vehicle weighing 38tonnes may be unable to withstand the impact of 60tonne truck crashing against it. Such accidents are infrequent but they can be lethal, like the accident which occurred in 2008 on the Italian A4 autostrade, which killed seven people.

Clearly, there is need for a modification of European Norm 1317 for Vehicle Restraint Systems to introduce a new containment level.

Meanwhile the UK’s 5125 Institute of Advanced Motorists (IAM) has called for roadside barriers to feature post protection so as to reduce the risk of injuries to motorcyclists.

The IAM have repeated calls for improvements to guardrail used along most British roads. It points out that these are designed to protect motorists inside trucks, cars or buses. For motorcyclists the barriers themselves pose a safety hazard, as a fallen rider can impact with the support posts causing serious injury or death. Technology does exist to deal with the issue such as fitting additional barrier sections or impact cushions, but these are not widely used across Europe and are only required as yet in Spain.

New research from Sweden shows that modern crash barriers actually provide no safety benefits to motorcyclists. Modern crash barriers are designed to save the lives of drivers, but amongst motorcyclists, hitting a crash barrier is a factor in 8-16% of fatal crashes, according to an IAM-sponsored study. Riders are fifteen times more likely to die after hitting a barrier than car occupants. Britain’s current barriers protect car occupants by redirecting the car away from the barrier and slowing it down over a short distance. The car’s body, seat belts and air bags also help to minimise injury. For motorcyclists, there is no such protection, leaving the rider’s body to take the full impact, resulting in serious injury or death.

Around 67% of all collisions between motorcyclists and crash barriers which result in death or serious injury include the rider either falling over or sliding under the crash barrier. Adding a shield to the barrier to prevent the rider from sliding underneath and colliding with support posts would reduce fatalities by up to a third. Crash barrier support posts can worsen the injuries of motorcyclists involved in an accident by five times. IAM director of policy and research Neil Greig said, “Our crash barriers are designed with cars in mind, but they can cause more harm than good for motorcyclists. Modifications are happening across Europe as governments recognise exactly how dangerous they are. Last year deaths and injuries of motorcyclists increased in the UK, so we must do more to protect them. Adding extra protection the barrier so that the posts aren’t exposed is a simple and cost-effective way to save lives.”

For more information on companies in this article

Related Content

  • Skidmarks: Hot Sauce
    February 25, 2020
    Our Skidmarks page is highly rated by readers. Your input could help make this page even more entertaining. If you come across any amusing road-related stories or pictures email me at [email protected]
  • Workzone safety protects workforce and drivers
    May 3, 2012
    Highway construction work zones are dangerous places, and anything that can improve safety is welcomed as Patrick Smith reports. The safe and efficient flow of traffic through work zones is a major concern to transportation officials, industry, the public, businesses, and commercial motor carriers. This is the view of the US Federal Highway Administration (FHWA), which has developed the Highway Work Zone Safety Program to reduce the fatalities and injurious crashes in work zones, and to enhance traffic oper
  • Modular crash cushions available
    June 28, 2013
    Italian specialist INDUSTRY AMS has developed a range of modular redirective crash cushions. The firm’s Safety Modular Absorber (SMA) models are available in different specifications to suit varying applications. The company claims that its novel SMA crash cushions are the most compact absorbers available on the market and these units meet the European safety requirements of the EN 1317-3 standard.
  • RB22 separators ''offer maximum safety''
    July 5, 2012
    Road traffic accidents are expensive and often frightening, and now most drivers will have encountered an average 80km/hr speed limit on a fast moving road. Keeping both lanes of traffic separate is the key to traffic safety, but when a driver loses control of a vehicle, and heads for the other lane of oncoming traffic, there is the potential for a serious accident. Having a barrier system in place that can keep the traffic safely separated reduces the risks for everyone concerned.