Italian manufacturer AMS provides safety by using honeycomb panels

Italian road safety firm Industry AMS has developed and patented high efficiency energy absorption systems provided with special metallic honeycomb panels. The SMA Crash Cushion was certified to the European Standard EN1317. It also tested successively against the US standard NCHRP in a frontal impact with a pickup truck provided with an anthropomorphic traffic device - and obtained the best Euro NCAP score.
May 6, 2016 Read time: 3 mins

Italian road safety firm Industry AMS has developed and patented high efficiency energy absorption systems provided with special metallic honeycomb panels.

The SMA Crash Cushion was certified to the European Standard EN1317. It also tested successively against the US standard NCHRP in a frontal impact with a pickup truck provided with an anthropomorphic traffic device - and obtained the best Euro NCAP score.

According to 7403 Industry AMS, the efficiency is guaranteed by high-tenacity steel which permits absorption through plastic deformation of the hexagonal cells of the impacting systems. On the basis of such honeycomb absorbing system, Industry AMS srl has developed a Crash Cushion Family (parallels and wide) certified according to EN1317, for the speed classes of 50, 80, 100 and 110km/h.

The use of a honeycomb absorbing system produces almost uniform absorption of energy during the entire crash cushion deformation. This prevents force peaks and consequent deceleration peaks, which are common in discontinuous energy absorption systems.

The company says that the energy absorption system is so efficient that it has been considered appropriate to prove the compliance of SMA Crash Cushion even with the stricter tests of the American NCHRP standard.

The Crash Cushion SMA 110, already tested and certified according to EN 1317, was subjected to a lateral and frontal test with a 2tonne pickup, according to the impact scenarios and TL TL 3:37 3:31 of NCHRP 350. In the case of frontal impact, the vehicle was equipped with crush test instrumented dummy able to calculate the biomechanical parameters related to the head, neck and chest and establish the damage and/or injury which would affect the vehicle occupants.

The use of a crush test instrumented dummy is then a direct method for the determination of injury to the occupants of the vehicle.

The ultimate goal of a road safety device is, in fact, to ensure safety of the occupants in case of impact and by using an instrumented dummy we quantitatively verified how the SMA Crash Cushion responds to this purpose.

In fact, the parameters that determine the performance of an impact Crash Cushion according to the 1317 standard, NCHRP and MASH are parameters of the vehicle and literature data show that these are not always related to the injuries to the vehicle occupants.

Ultimately, the SMA 110 Crash Cushion successfully underwent two additional shocks performed according to NCHRP 350. The company says that makes it almost completely compliant with the two main reference standards.

Road Markings, Barriers & Workzone Protection

For more information on companies in this article

Related Content

  • Proper GPR Surveying Techniques
    May 10, 2019
    A sustainably good road surface often depends on how well understood is the ground underneath the road’s route. Brian Jones* offers some best practice and advice for getting the most from ground-penetrating radar investigations Ground-penetrating radar (GPR) is one of the most accurate non-destructive testing (NDT) methods available. To get the most from GPR surveying, it is absolutely essential to understand how GPR tools work and follow best practices when conducting surveys. Key areas to be aware o
    Read More
  • An array of crushing and screening innovations was presented at the recent INTERMAT 2012 exhibition
    July 19, 2012
    The crushing and screening phase is a crucial component in aggregate production and new development will help optimise performance - Mike Woof reports Crushing and screening is a key part of the quarrying cycle and has a huge impact on overall operating performance. Optimising operations will cut running costs, reduce materials wastage and also provide a more consistent product quality, boosting cost-effectiveness dramatically. An array of innovations were revealed to the market at the recent INTERMAT 2012
    Read More
  • Rockmore’s new DTH hammer drill
    March 12, 2018
    Rockmore International is adding its new ROK 550T drill to its T Series DTH hammer line. The T Series DTH hammers are TUBELESS and use drill bits featuring industry standard shank connections without the embedded plastic blow tube/foot valve. The firm’s first T Series DTH model was the ROK 600T, a 152mm class model that uses a tubeless QL6/QL60 bit shank. The company then expanded the T Series with the ROK 60T-360T hammers that use the IR 360 bit shank without the blow tube/foot valve. And Rockmore is now
    Read More
  • Accurate weigh-in-motion technology
    June 21, 2016
    Weigh-in-motion technology is ensuring increasingly accurate, and flexible, weighing stations. Weigh-in-motion specialist manufacturer Axtec says that its space-saving dynamic weighbridge is accurate to within ±0.5% and is the most precise system in the world. From its Runcorn, UK manufacturing facility, Axtec undertakes research and development of new technologies, as well as software testing, fabrication, construction and installation of WIM products. Axtec’s axle weighing platform design is intended f
    Read More

Highlighted Content