Italian manufacturer AMS provides safety by using honeycomb panels

Italian road safety firm Industry AMS has developed and patented high efficiency energy absorption systems provided with special metallic honeycomb panels. The SMA Crash Cushion was certified to the European Standard EN1317. It also tested successively against the US standard NCHRP in a frontal impact with a pickup truck provided with an anthropomorphic traffic device - and obtained the best Euro NCAP score.
May 6, 2016 Read time: 3 mins

Italian road safety firm Industry AMS has developed and patented high efficiency energy absorption systems provided with special metallic honeycomb panels.

The SMA Crash Cushion was certified to the European Standard EN1317. It also tested successively against the US standard NCHRP in a frontal impact with a pickup truck provided with an anthropomorphic traffic device - and obtained the best Euro NCAP score.

According to 7403 Industry AMS, the efficiency is guaranteed by high-tenacity steel which permits absorption through plastic deformation of the hexagonal cells of the impacting systems. On the basis of such honeycomb absorbing system, Industry AMS srl has developed a Crash Cushion Family (parallels and wide) certified according to EN1317, for the speed classes of 50, 80, 100 and 110km/h.

The use of a honeycomb absorbing system produces almost uniform absorption of energy during the entire crash cushion deformation. This prevents force peaks and consequent deceleration peaks, which are common in discontinuous energy absorption systems.

The company says that the energy absorption system is so efficient that it has been considered appropriate to prove the compliance of SMA Crash Cushion even with the stricter tests of the American NCHRP standard.

The Crash Cushion SMA 110, already tested and certified according to EN 1317, was subjected to a lateral and frontal test with a 2tonne pickup, according to the impact scenarios and TL TL 3:37 3:31 of NCHRP 350. In the case of frontal impact, the vehicle was equipped with crush test instrumented dummy able to calculate the biomechanical parameters related to the head, neck and chest and establish the damage and/or injury which would affect the vehicle occupants.

The use of a crush test instrumented dummy is then a direct method for the determination of injury to the occupants of the vehicle.

The ultimate goal of a road safety device is, in fact, to ensure safety of the occupants in case of impact and by using an instrumented dummy we quantitatively verified how the SMA Crash Cushion responds to this purpose.

In fact, the parameters that determine the performance of an impact Crash Cushion according to the 1317 standard, NCHRP and MASH are parameters of the vehicle and literature data show that these are not always related to the injuries to the vehicle occupants.

Ultimately, the SMA 110 Crash Cushion successfully underwent two additional shocks performed according to NCHRP 350. The company says that makes it almost completely compliant with the two main reference standards.

Road Markings, Barriers & Workzone Protection

For more information on companies in this article

Related Content

  • The cycle of potholes in the UK
    October 1, 2019
    Since 2015 almost a million potholes have been recorded annually by UK local authorities, with the 2016 count reaching 1,088,965, according to an insurance provider.
    Read More
  • Effective precast barrier units from Netherlands firm
    April 29, 2015
    Haitsma Beton in the Netherlands has developed a lightweight precast concrete barrier system for temporary use. This T3 system is said to make investing in vehicle guidance more cost-effective. Each HaiSafe T barrier weighs 1.5tonnes and is over 10% lighter than comparable precast concrete barriers. The system is said to be easy and quick to locate, as well as to to assemble and disassemble. A novel feature is that no anchoring is needed at the ends, because the system has been tested and approved without a
    Read More
  • Crushing and screening for producing and re-using
    July 23, 2012
    The recycling and minerals extraction markets now share technologies, Mike Woof reports Not surprisingly, the Steinexpo quarrying event in Germany was a key launch venue for new crushing and screening technologies, as well as associated quarrying technology. Crushing and screening equipment firms from a wide range of European countries including Austria, the Czech Republic, Germany, Ireland, Italy, Sweden, Switzerland and the UK were present at the exhibition. However it was noticeable how closely the miner
    Read More
  • Bitumen additives raise environmental questions
    February 14, 2012
    New products, including additives, are coming onto the market to help reduce the cost of producing bitumen. Patrick smith reports. According to Eng. Paolo Visconti of Iterchimica, environmental issues and the health and safety of operators of manufacturing plants and workers laying bituminous mixes have raised long debates on the possible harmfulness of fumes which are emitted when heating these mixes at the temperatures (160-180°C) required for their production. "If, on the one hand, the effects on operato
    Read More

Highlighted Content