Skip to main content

Italian manufacturer AMS provides safety by using honeycomb panels

Italian road safety firm Industry AMS has developed and patented high efficiency energy absorption systems provided with special metallic honeycomb panels. The SMA Crash Cushion was certified to the European Standard EN1317. It also tested successively against the US standard NCHRP in a frontal impact with a pickup truck provided with an anthropomorphic traffic device - and obtained the best Euro NCAP score.
May 6, 2016 Read time: 3 mins

Italian road safety firm Industry AMS has developed and patented high efficiency energy absorption systems provided with special metallic honeycomb panels.

The SMA Crash Cushion was certified to the European Standard EN1317. It also tested successively against the US standard NCHRP in a frontal impact with a pickup truck provided with an anthropomorphic traffic device - and obtained the best Euro NCAP score.

According to 7403 Industry AMS, the efficiency is guaranteed by high-tenacity steel which permits absorption through plastic deformation of the hexagonal cells of the impacting systems. On the basis of such honeycomb absorbing system, Industry AMS srl has developed a Crash Cushion Family (parallels and wide) certified according to EN1317, for the speed classes of 50, 80, 100 and 110km/h.

The use of a honeycomb absorbing system produces almost uniform absorption of energy during the entire crash cushion deformation. This prevents force peaks and consequent deceleration peaks, which are common in discontinuous energy absorption systems.

The company says that the energy absorption system is so efficient that it has been considered appropriate to prove the compliance of SMA Crash Cushion even with the stricter tests of the American NCHRP standard.

The Crash Cushion SMA 110, already tested and certified according to EN 1317, was subjected to a lateral and frontal test with a 2tonne pickup, according to the impact scenarios and TL TL 3:37 3:31 of NCHRP 350. In the case of frontal impact, the vehicle was equipped with crush test instrumented dummy able to calculate the biomechanical parameters related to the head, neck and chest and establish the damage and/or injury which would affect the vehicle occupants.

The use of a crush test instrumented dummy is then a direct method for the determination of injury to the occupants of the vehicle.

The ultimate goal of a road safety device is, in fact, to ensure safety of the occupants in case of impact and by using an instrumented dummy we quantitatively verified how the SMA Crash Cushion responds to this purpose.

In fact, the parameters that determine the performance of an impact Crash Cushion according to the 1317 standard, NCHRP and MASH are parameters of the vehicle and literature data show that these are not always related to the injuries to the vehicle occupants.

Ultimately, the SMA 110 Crash Cushion successfully underwent two additional shocks performed according to NCHRP 350. The company says that makes it almost completely compliant with the two main reference standards.

For more information on companies in this article

Related Content

  • Concrete testing - defining standards
    February 13, 2012
    Concrete is a versatile construction product, but it must be tested to make sure that it is fit for purpose
  • Steel wire barriers provide rock fall protection
    February 6, 2012
    In Gibraltar, where the entire population lives on or close to the huge limestone rock that gives the nation its name, the issue of rock fall protection is taken very seriously. Here, a scheme to install a network of rock fall catchment fences has just been completed, which will allow the re-opening of a critically important road at the south-eastern end of the Rock, which was closed following a significant rock fall occurrence in 2002.
  • Stronger crash barriers may be needed for heavier trucks
    January 4, 2013
    The European Road Federation (ERF) has voiced its concern that roadside barriers in Europe may have to be upgraded According to the ERF, the recent decision of the European Commission to allow cross-border movement of longer and heavier trucks, it is keen to raise awareness of the important implications such a move may have for road barriers. ‘Road safety barriers are designed and tested according to the maximum weight of vehicles circulating on Europe’s roads. The current European Norm (EN 1317) allows for
  • A flexible approach to concrete testing
    February 20, 2012
    One of the world's most versatile building materials is subject to a variety of tests to make sure it is fit for purpose. Patrick Smith reports