Fast drying road marking for all surfaces

Ennis Prismo continues to expand its range of road marking products with the addition of two new solutions. One is used to form temporary markings and the other to provide more permanent lines. The two products are known as Easymark Temporary and Easymark Permanent respectively. These fast drying aerosols can be used in car parks and on roads and are non harmful to the environment and aquatic life. Both Easymark products can be used on a range of surfaces including asphalt, concrete, metal and timber. Compe
February 15, 2012 Read time: 2 mins

1394 Ennis Prismo continues to expand its range of road marking products with the addition of two new solutions. One is used to form temporary markings and the other to provide more permanent lines.

The two products are known as Easymark Temporary and Easymark Permanent respectively. These fast drying aerosols can be used in car parks and on roads and are non harmful to the environment and aquatic life. Both Easymark products can be used on a range of surfaces including asphalt, concrete, metal and timber. Competitively-priced, these line markings have been specifically designed to cater for longer term, or short term performance. Easymark Permanent will produce distinctive lines that are expected to last 6-12 months, depending upon the traffic volumes. Clean, accurate lines can be achieved with the two, or four wheel applicators, while the marker is resistant to most chemicals and is chlorofluorocarbon (CFC) free.

Easymark Temporary is formulated specifically for creating shortterm, low-cost markings that will fade after some six weeks, again depending upon traffic volumes.

This product is suited for creating provisional markings in areas where low wear applications are required or where markings are required to fade or disappear shortly after work has been completed, eliminating the need for mechanical removal.

If required, Easymark Temporary markings can be removed instantly with a pressure hose and brush.

Both are available in six colours; white, yellow, blue, red, green and black. Each 750ml aerosol has sufficient capacity to form a 100m long line at a width of 50mm.

Both can be applied by applicator or hand and in conjunction with stencil kits, can also be used to form letters and numbers.
Road Markings, Barriers & Workzone Protection

For more information on companies in this article

Related Content

  • Better road surfaces to last longer
    August 23, 2013
    Preservation can make roads perform better and last longer - and save money in the long run. Kristina Smith reports BAM Wegen has laid the first ever half-warm porous asphalt section on a major highway in the Netherlands. The asphalt for the 500m-long test section on the A18 near Varsseveld was produced at 105°C rather than 160°C, representing a saving on energy and CO2 emissions of around 30%.
    Read More
  • The hanging Honda
    August 10, 2018
    Police in Toronto are still mystified as to how and why a stripped-out Honda was left dangling from a busy bridge. At first it was thought the car had been placed there as part of a movie shoot, but it was quickly realised that this was not the case and no request had been filed to carry out such a stunt. The car was stripped of any identification as well as many mechanical components, reducing its weight sufficiently for it to be suspended from a single cable. After a period left hanging, the vehicle was l
    Read More
  • Optimising operations with construction software gains
    May 20, 2015
    Innovations in construction software are helping boost project efficiency and optimising project operations – Clive Davidson writes Over the past decade, while construction engineers have been putting up buildings or infrastructure, software engineers have been developing a parallel universe where virtual buildings or infrastructure can be created in ever increasing detail. What started with 2D architectural drawings in computer-aided design (CAD) systems, has become a multi-dimensional world, with 3D ge
    Read More
  • Advanced, low emission, fuel efficient earthmoving
    February 23, 2012
    Manufacturers are rolling out sophisticated machines for the European, North American and Japanese markets - Mike Woof reports. This year has been a pivotal period for the development of advanced, low emission earthmoving machines. During 2011 an array of manufacturers have introduced new models designed to comply with the latest Stage IIIB/Tier 4 Interim emissions regulations introduced for
    Read More

Highlighted Content