Energy absorbing safety barrier

Barrier Systems says that its new tensioned barrier offers high energy absorbing capabilities in head-on collisions. The company says that this is because the X-Tension technology is a tension-based solution rather than compression-based. The new range delivers good performance in these applications, as energy is absorbed with resistance at the impact head rather than being transferred down the rail as occurs with other systems. Even high-angle (15° during testing) impacts on the nose resulted in the vehicl
March 9, 2012 Read time: 3 mins

165 Barrier Systems says that its new tensioned barrier offers high energy absorbing capabilities in head-on collisions.

The company says that this is because the X-Tension technology is a tension-based solution rather than compression-based. The new range delivers good performance in these applications, as energy is absorbed with resistance at the impact head rather than being transferred down the rail as occurs with other systems. Even high-angle (15° during testing) impacts on the nose resulted in the vehicle being redirected and controlled rather than passing to the backside of the terminal at high speed. For side impacts, tension in the rail is transferred by cables to the foundation anchor to provide containment and redirection.

The company also has an ABSORB 350 product that is non-redirective and is designed as a gating crash cushion. The system offers a reliable and easy method of protecting the ends of concrete barriers and can be attached to the end of permanent or portable concrete barriers, without the need to anchor the system to the roadway surface.

At 610mm wide, it is suited for narrow areas where road and workspace is limited. ABSORB 350 is easy to install and is easier to restore after an impact than other non-redirective, gating crash cushions. Tests show the product meets the rigorous requirements of NCHRP Report 350, Test Levels 2 (70 km/h) and 3 (100 km/h). This system is designed for use on narrow hazards for exits, wide medians, edge of road locations and locations.

Meanwhile the BarrierGuard 800 is a rapidly deployable Steel Safety Barrier for use in work zones or as a permanent installation. The system offers extremely attractive costs compared to portable concrete barrier since 180m can be delivered to a job site in one truck load. The system is also quick to assemble on site due to its connection system which uses only one bolt, allowing a crew of three to install up to 300m/hour. Featuring a step profile the barrier can redirect errant vehicles while causing little damage to either alnd also meets the tough NCHRP Report 350, Test Level 4.

Lastly, the firm's PaveGuard system offers continuous positive barrier protection during paving operations for workers, motorists and equipment. The system is on wheels and is pulled as the project advances and can be attached to a vehicle when it has to be moved. The system can be loaded and unloaded without the need for special equipment and does not require electrical power or sophisticated control systems.
Road Markings, Barriers & Workzone Protection

For more information on companies in this article

Related Content

  • Zipping up road lanes
    September 28, 2018
    QMB has a Lindsay Road Zipper on duty near Montreal. World Highways deputy editor David Arminas climbed aboard As vice president of Canadian barrier specialist QMB, based in Laval, Quebec, Marc-Andre Seguin is sanguine about the future for moveable barriers. On the one hand, it looks good. The oft-stated advantage of moveable barriers is that the systems are cheaper to install than adding a lane or two to a highway or bridge. Directional changes to lanes can boost volume on a road without disrupting tra
    Read More
  • Safety measures aid workzone accident reduction
    February 20, 2012
    Everyone connected with the highway industry is involved in the efforts to cut down the number of work zone accidents. Patrick Smith reports. A few months ago, as road work resumed on America's highways and bridges, US Transportation Secretary Ray LaHood called on drivers to use extra caution in work zones. At the same time he commended the success in reducing overall roadway fatalities in each of the last seven years.
    Read More
  • Safer with REBLOC 185A barriers
    February 15, 2022
    The concrete 185A is an extensively tested and fully EN 1317-1/2 compliant safety barrier with highest containment levels H4a and H4b.
    Read More
  • Modular crash cushions available
    June 28, 2013
    Italian specialist INDUSTRY AMS has developed a range of modular redirective crash cushions. The firm’s Safety Modular Absorber (SMA) models are available in different specifications to suit varying applications. The company claims that its novel SMA crash cushions are the most compact absorbers available on the market and these units meet the European safety requirements of the EN 1317-3 standard.
    Read More

Highlighted Content