Energy absorbing safety barrier

Barrier Systems says that its new tensioned barrier offers high energy absorbing capabilities in head-on collisions. The company says that this is because the X-Tension technology is a tension-based solution rather than compression-based. The new range delivers good performance in these applications, as energy is absorbed with resistance at the impact head rather than being transferred down the rail as occurs with other systems. Even high-angle (15° during testing) impacts on the nose resulted in the vehicl
March 9, 2012 Read time: 3 mins

165 Barrier Systems says that its new tensioned barrier offers high energy absorbing capabilities in head-on collisions.

The company says that this is because the X-Tension technology is a tension-based solution rather than compression-based. The new range delivers good performance in these applications, as energy is absorbed with resistance at the impact head rather than being transferred down the rail as occurs with other systems. Even high-angle (15° during testing) impacts on the nose resulted in the vehicle being redirected and controlled rather than passing to the backside of the terminal at high speed. For side impacts, tension in the rail is transferred by cables to the foundation anchor to provide containment and redirection.

The company also has an ABSORB 350 product that is non-redirective and is designed as a gating crash cushion. The system offers a reliable and easy method of protecting the ends of concrete barriers and can be attached to the end of permanent or portable concrete barriers, without the need to anchor the system to the roadway surface.

At 610mm wide, it is suited for narrow areas where road and workspace is limited. ABSORB 350 is easy to install and is easier to restore after an impact than other non-redirective, gating crash cushions. Tests show the product meets the rigorous requirements of NCHRP Report 350, Test Levels 2 (70 km/h) and 3 (100 km/h). This system is designed for use on narrow hazards for exits, wide medians, edge of road locations and locations.

Meanwhile the BarrierGuard 800 is a rapidly deployable Steel Safety Barrier for use in work zones or as a permanent installation. The system offers extremely attractive costs compared to portable concrete barrier since 180m can be delivered to a job site in one truck load. The system is also quick to assemble on site due to its connection system which uses only one bolt, allowing a crew of three to install up to 300m/hour. Featuring a step profile the barrier can redirect errant vehicles while causing little damage to either alnd also meets the tough NCHRP Report 350, Test Level 4.

Lastly, the firm's PaveGuard system offers continuous positive barrier protection during paving operations for workers, motorists and equipment. The system is on wheels and is pulled as the project advances and can be attached to a vehicle when it has to be moved. The system can be loaded and unloaded without the need for special equipment and does not require electrical power or sophisticated control systems.
Road Markings, Barriers & Workzone Protection

For more information on companies in this article

Related Content

  • Major upgrade for Chicago O’Hare Airport
    August 14, 2015
    Internationally, airports are being upgraded and expanded to increase capacity and safety – Mike Woof writes. All around the world, airports are being expanded and upgraded, both to cope with massive increases in passenger numbers and also to handle larger aircraft. Runways have to be rebuilt with stronger structures and surfaces to handle greater air traffic volumes as well as increased loads from larger aeroplanes. Building airport runways, however, poses many challenges for construction crews. Paving qua
    Read More
  • Doka’s Voest Bridge bypass project
    February 10, 2020
    The Voest Bridge over the Danube River is part of the A7 Mühlkreis Autobahn through Linz, Austria, is 40 years. Two bypass bridges are being constructed alongside the existing cable-stayed bridge as part of the client ASFINAG’s strategy to boost traffic capacity - around 100,000 vehicles cross the old bridge each day.
    Read More
  • Final beam for Gerald Desmond Bridge replacement
    May 1, 2020
    The US$1.47 billion project was started in 2013 and open later this year.
    Read More
  • Stronger crash barriers may be needed for heavier trucks
    November 26, 2012
    The European Road Federation (ERF) has voiced its concern that roadside barriers in Europe may have to be upgraded. Meanwhile the UK’s Institute of Advanced Motorists (IAM) has called for roadside barriers to feature post protection so as to reduce the risk of injuries to motorcyclists. According to the ERF, the recent decision of the European Commission to allow cross-border movement of longer and heavier trucks, it is keen to raise awareness of the important implications such a move may have for road barr
    Read More

Highlighted Content