Skip to main content

RMD’s Hong Kong highway project

RMD Kwikform has supplied its 80kN Rapidshor shoring for the widening of the Tolo Highway, running between the Island House Interchange and Tai Hang in Hong Kong. The project, overseen by main contractor Gammon Construction and set to be completed by the end of 2013, will widen the Tolo Highway from a two to four-lane carriageway in each direction, alleviating traffic congestion. “We were approached by [project] sub-contractors, United Soundfair and Richwell Engineering to supply shoring and formwork suppor
June 13, 2012 Read time: 2 mins
319 RMD Kwikform has supplied its 80kN Rapidshor shoring for the widening of the Tolo Highway, running between the Island House Interchange and Tai Hang in Hong Kong.

The project, overseen by main contractor 1526 Gammon Construction and set to be completed by the end of 2013, will widen the Tolo Highway from a two to four-lane carriageway in each direction, alleviating traffic congestion.

“We were approached by [project] sub-contractors, United Soundfair and Richwell Engineering to supply shoring and formwork support,” says Noel Kennedy, general manager for RMD Kwikform Hong Kong.

“The scale of the site and project required the use of our 80kN capacity Rapidshor shoring, to ensure safety and the continuous traffic flow needed, whilst the widening took place. Due to the location of the site, we also needed to engineer a solution using Rapidshor to support the overhead works spanning the slip roads at interchanges, whilst maintaining a safe access route for traffic.

“In addition to the main Rapidshor shoring, we also utilised our Megashor heavy duty shoring to provide extra support to a variety of the bridge deck structures, some up to a height of 25metres,  with SuperSlim and GTX Beams used to create the soffit.”

Kennedy says the Tolo Highways project is one of many that have benefitted from the use of Rapidshor, which is one of the more widely used systems in Hong Kong. RMD Kwikform says it’s popular with sub-contractors, as it allows them to use less labour, due to the heavy leg load capacity.

For more information on companies in this article

Related Content

  • Tubeshor shoring system
    December 10, 2024

    Altrad RMD Kwikform has launched a solution to reduce the effects of thermal loading - the Tubeshor Active Thermal Compensator, ATC.

    The Tubeshor hybrid hydraulic shoring system is used for propping waler beams or capping beams of large excavations. Altrad RMD Kwikform, an above and below ground temporary works specialist, said it comes in a range of diameters to cater for all duties of shoring requirement.

  • Vital structures
    February 10, 2012
    A wide variety of products are available to help bridge owners reduce the need for costly repairs. Bridges are one of the most expensive structures on a highway system, and their maintenance, and where necessary, repair will save millions over time. Prevention being better than cure means that anything that can be done to reduce the need for repair is a good investment. For example, a MOOG bucket-type inspection unit has been commissioned for the Naini Bridge in Allahabad in the state of Uttar Pradesh, Indi
  • Bridges in Sunderland and Poland are being slid into place
    February 6, 2017
    Sunderland sees a bridge slide into place and two bridges inch their way across a Polish highway Slowly but surely, a 2,500 tonne section of a new bridge deck was eased out from the banks of the River Wear near Sunderland in northern England. It now straddles the water, pointing towards the opposite bank which it will eventually reach after another sliding operation likely to take place next year. The project to build the New Wear Crossing is now halfway through with the first half of the steel deck b
  • Major award for RMD Kwikform
    February 7, 2012
    UK-headquartered, global construction product specialist RMD Kwikform has been awarded the prestigious Queen's Award for Enterprise: International Trade 2010.