Skip to main content

Fast repair for key Cairo road

Fast repair of Cairo’s busy urban highway has been achieved using paving equipment. And MOBA levelling technology played an important role in ensuring finish quality met requirements. Cairo is Egypt’s fast-growing capital city, with an estimated population of around 20 million living in its catchment area. The city’s fast growth rate however has placed enormous demands on its infrastructure, with transportation creaking under the strain. An increasing numbers of people use the roads in and around Cairo ev
July 14, 2015 Read time: 3 mins
Using the MOBA equipment on the Cairo road project optimised paving quality and productivity
Fast repair of Cairo’s busy urban highway has been achieved using paving equipment. And MOBA levelling technology played an important role in ensuring that finish quality met requirements

Cairo is Egypt’s fast-growing capital city, with an estimated population of about 20 million living in its catchment area. The city’s fast growth rate, however, has placed enormous demands on its infrastructure, with transportation creaking under the strain. An increasing number of people use the roads in and around Cairo every day, resulting in ever more frequent and longer traffic jams, especially at peak times. This is also true for the city’s 100km long orbital highway, Cairo's most important traffic artery, which was built in the 1980s. In the 1990-2000 period, the number of vehicles rose from 38,000 to 100,000 per day. And this number continued to increase unchecked in the following years. Owing to repair backlogs and severe wear, the road surface had many cracks and potholes and was in dire need of repair. In spring 2015, the road surface along a 30km section of the eight-lane orbital route to the west of the city was removed and a new 50mm thick surface layer was laid.
Construction company General Nile Company for Road Construction (GNCRC) was able to optimise quality and productivity, however, using the 1228 MOBA-matic levelling system with the Big Sonic-Ski on either side of its 1222 Terex CR462 paver.

The Big Sonic-Ski is a combination of up to four ultrasound sensors attached to a flexible 13m long system. The Big Sonic-Ski uses this to scan the substrate at various, widely spaced points. Each Sonic-Ski emits five beams for height measurement. The measurement values with the greatest deviations are discarded in order to rule out false measurements caused by, for example, stones lying on the reference. The sensor derives an average value from the remaining measurements. With the Big Sonic-Ski, which combines three or four sensors, all of the sensors send their measurement values to the MOBA-matic. The MOBA-matic calculates an average value so that even long sections of unevenness can be detected and smoothed out during asphalting by means of automatic adjustment of the screed.
With this solution, it was possible to avoid complete closure of the highway and to complete the repair work quickly. And because the pavers only worked during the night, the effect on the traffic was minimised so that no additional traffic jams were caused. The use of the ultrasound system that operates without a reference was the best possible solution because the milled-off surface was extremely uneven and had many milling cavities.

Without a levelling system, this reference unevenness would have been copied – the new road would then be quickly damaged again because unevenness not only reduces driving comfort, it also increases susceptibility to potholes and cracks.

The only possible alternative to the Big Sonic-Ski would have been to use a levelling system in combination with a string line as reference because the kerbstone had too many holes and was too uneven to be used as a reference. But using a string line would not only have been expensive and more time-consuming, it would have made it necessary to close the road, which in view of the traffic situation was impossible.

The contractor was supported by Egytitans Engineering, MOBA partner in Egypt, that supervised equipment of the machinery.

For more information on companies in this article

Related Content

  • Self-healing roads, slippery roads and slimmer roads
    November 24, 2017
    This month’s bitumen technology pages bring you self-healing roads, slippery roads and slimmer roads and explains why one UK contractor has started manufacturing its own polymer modified bitumen - Kristina Smith reports. Professor Erik Schlangen, who heads up experimental micromechanics at the Delft University of Technology is receiving calls from all round the world these days. And it is hardly surprising because he and his team have invented a great new technology: asphalt that heals itself.
  • CRCP is first choice for Belgian highway
    November 28, 2012
    Dan Gilkes reports on a Belgian highway upgrade When the Ministry of Public Works in the Belgian State of Flanders decided to reconstruct and resurface 19km of the N49 Antwerp-Knokke Expressway, continuously reinforced concrete paving (CRCP) with an exposed aggregate surface was the natural material choice. Indeed exposed aggregate, with its high grip and low noise benefits, has been the first option for all motorway surfacing work in Belgium since the 1980s. However, the €15.65 million contract is not a li
  • Versatile recycling option
    February 28, 2012
    A pavement recycling contractor in eastern New York State in the US is using an innovative and versatile Wirtgen machine to carry out very different road rehabilitation tasks. This unit is being used to lay foamed bitumen-recycling pavements as well as carrying out cold-milling.
  • A new grader and dozer control system is offered by MOBA
    January 6, 2017
    MOBA is offering a sophisticated control system for use with bulldozers and graders available in both 2D and 3D format. The company says that its 3D-matic package offers precise and versatile levelling control for graders and dozers and which can also be used as a 2D system if necessary. Marketing manager Christine Seidel said, “This system moves the blade. Our mindset is to make it easy to use for the operator. It’s different from the competition which focus on tonnages as this is focussed on the machine a