Skip to main content

Fast repair for key Cairo road

Fast repair of Cairo’s busy urban highway has been achieved using paving equipment. And MOBA levelling technology played an important role in ensuring finish quality met requirements. Cairo is Egypt’s fast-growing capital city, with an estimated population of around 20 million living in its catchment area. The city’s fast growth rate however has placed enormous demands on its infrastructure, with transportation creaking under the strain. An increasing numbers of people use the roads in and around Cairo ev
July 14, 2015 Read time: 3 mins
Using the MOBA equipment on the Cairo road project optimised paving quality and productivity
Fast repair of Cairo’s busy urban highway has been achieved using paving equipment. And MOBA levelling technology played an important role in ensuring that finish quality met requirements

Cairo is Egypt’s fast-growing capital city, with an estimated population of about 20 million living in its catchment area. The city’s fast growth rate, however, has placed enormous demands on its infrastructure, with transportation creaking under the strain. An increasing number of people use the roads in and around Cairo every day, resulting in ever more frequent and longer traffic jams, especially at peak times. This is also true for the city’s 100km long orbital highway, Cairo's most important traffic artery, which was built in the 1980s. In the 1990-2000 period, the number of vehicles rose from 38,000 to 100,000 per day. And this number continued to increase unchecked in the following years. Owing to repair backlogs and severe wear, the road surface had many cracks and potholes and was in dire need of repair. In spring 2015, the road surface along a 30km section of the eight-lane orbital route to the west of the city was removed and a new 50mm thick surface layer was laid.
Construction company General Nile Company for Road Construction (GNCRC) was able to optimise quality and productivity, however, using the 1228 MOBA-matic levelling system with the Big Sonic-Ski on either side of its 1222 Terex CR462 paver.

The Big Sonic-Ski is a combination of up to four ultrasound sensors attached to a flexible 13m long system. The Big Sonic-Ski uses this to scan the substrate at various, widely spaced points. Each Sonic-Ski emits five beams for height measurement. The measurement values with the greatest deviations are discarded in order to rule out false measurements caused by, for example, stones lying on the reference. The sensor derives an average value from the remaining measurements. With the Big Sonic-Ski, which combines three or four sensors, all of the sensors send their measurement values to the MOBA-matic. The MOBA-matic calculates an average value so that even long sections of unevenness can be detected and smoothed out during asphalting by means of automatic adjustment of the screed.
With this solution, it was possible to avoid complete closure of the highway and to complete the repair work quickly. And because the pavers only worked during the night, the effect on the traffic was minimised so that no additional traffic jams were caused. The use of the ultrasound system that operates without a reference was the best possible solution because the milled-off surface was extremely uneven and had many milling cavities.

Without a levelling system, this reference unevenness would have been copied – the new road would then be quickly damaged again because unevenness not only reduces driving comfort, it also increases susceptibility to potholes and cracks.

The only possible alternative to the Big Sonic-Ski would have been to use a levelling system in combination with a string line as reference because the kerbstone had too many holes and was too uneven to be used as a reference. But using a string line would not only have been expensive and more time-consuming, it would have made it necessary to close the road, which in view of the traffic situation was impossible.

The contractor was supported by Egytitans Engineering, MOBA partner in Egypt, that supervised equipment of the machinery.

For more information on companies in this article

Related Content

  • Repair, recycling and warm mix technology at Italy’s Asphaltica exibition
    May 15, 2017
    As the name might suggest, the Asphaltica show in Verona, Italy was a good place to catch up on new ideas and applications for bitumen technology. Kristina Smith picked out a few highlights.
  • Traffic control to beat congestion
    November 6, 2012
    Max Lay discusses how congestion has posed problems throughout history from early civilisation to the present day One of the earliest known human settlements was at the Springs of Elisha at Jericho. Inevitably, locals collecting fresh water from the springs would encounter other water carriers. When a path was too narrow, or access to it was too limited, or it crossed another path, some carriers would find it necessary to stand aside for others. Priority in such cases might be based on common courtesy and p
  • Highway widening project for the US
    April 19, 2018
    A highway widening project in the US state of New Hampshire is being assisted by the use of a gravity-fed asphalt paver. The widening work is being carried out as part of an upgrade for a 32km stretch of I-93, which was started eight years ago. The work is being carried out for the New Hampshire Department of Transportation (NHDOT) on a section of the highway between Exits 1 and 5 from the Massachusetts Stateline to Manchester, NH. According to NHDOT, the project involves widening I-93 from two lanes in
  • Smooth sailing for paving with Topcon’s SmoothRide
    April 14, 2016
    Topcon Positioning Group’s new road scanning solution SmoothRide can gather highway asset data at highway speeds with no need for lane closures, crash trucks or escorts. SmoothRide is a vehicle-mounted resurfacing solution for paving and milling projects. It uses a combination of core Topcon technologies designed to deliver the smoothest surface possible, while efficiently managing the quantity of material for each project.