Skip to main content

Are drones homing in on road construction?

It may be early days for using drones – unmanned aerial systems (UAS) -- to map construction sites, but technology and legislation are moving in that direction. At the moment drones can fly within only a 500m radius of the ‘pilot’ standing on the ground, making the flight area a 1km diameter. This is the key limiting issue for any sector, especially road construction, says Jonathan Gill, a robotics engineer and a qualified drone pilot for the past seven years. The logic is that a drone remains withi
August 4, 2015 Read time: 4 mins
It may be early days for using drones – unmanned aerial systems (UAS) - to map

construction sites, but technology and legislation are moving in that direction.

At the moment drones can fly within only a 500m radius of the ‘pilot’ standing on the ground, making the flight area a 1km diameter. This is the key limiting issue for any sector, especially road construction, says Jonathan Gill, a robotics engineer and a qualified drone pilot for the past seven years.

The logic is that a drone remains within eyesight of the pilot so he or she can avoid obstacles – including other drones and aircraft that may be landing.

Given that, a highways contractor can get a view of only 1km stretch of road at most. Less, if the drone would be out of eyesight of the pilot, said Gill, who also has experience in subsea remotely operated vehicles for the petrochemical industry. Economies of scale for operating a drone would be for longer stretches of road. As it stands, to survey a 10km stretch of road, the drone would have to take off and land many times to collect the required data.

Also, for out-of-sight flying, drones would need some sophisticated electronics for vision aid and obstacle detection.

The agricultural sector, however, is moving ahead with greater drone use. Gill, a visiting researcher at Harper Adams University, an agricultural college in western England, recently started working with international UAS provider PrecisionHawk. Harper Adams is delivering drone training in exchange for aerial imagery of the university campus.

PrecisionHawk has been flying one of its Lancaster vehicles as part of a training and demonstration session for its users. During the session, a range of photographs were taken of a trials field that has been used to assess the effect of farm traffic on crop yields and soil structure.

The collaboration is through the university’s UAS Special Interest Group, a membership group focused on the application of unmanned aerial systems in agriculture. “Harper Adams is looking for partners to work with to develop see-and-avoid systems,” said Gill. “The trouble is that the technology is moving so fast that governmental legislation is always trying to catch up.”

Some parts of the construction sector have taken up the technology quicker than others, such as aggregates. For instance, a gravel pit operator could spend two days operating a drone to quantify spoil heaps versus a week or so using surveyors,” he said.

Last year, contractor 2319 Costain reported that it had successfully used a miniature unmanned helicopter (pictured) for aerial photography on a contract to dual the A8 road between Belfast and Larne in Northern Ireland. The consortium, also comprising 2340 Lagan Construction and 2717 Ferrovial Agroman, is responsible for creating 14.5km of new roadway in the €185 million scheme on behalf of the Northern Ireland’s Department for Regional Development’s Roads Service.

Costain said in a written statement that the four-rotor drone, measuring around 350mm square and with a bolt-on video camera, made several test flights over the road. It also assisted following a road traffic accident.

“One of the surveyors who works for one of the other joint venture partners has set himself up as an operator of this aircraft and was using the project as a bit of a testbed, as a test of its capabilities and to help him get his licence,” explained John Lee, deputy project manager for the consortium.

Costain had previously used full-size aircraft to carry out aerial photography. But the new drone helicopter has several potential advantages over manned aircraft. “With real aircraft, there are limitations in terms of how low it can fly and weather can be a problem,” Lee said at the time.

“With one of these helicopters, you can hover and get in close to structures. You have high-definition quality footage and you can take stills from that, as well as obvious health and safety benefits from not placing people at risk from working at height.”

The cost of using the mini-helicopter is also a fraction of that of a manned aircraft, said Lee. Costain also noted at the time that it would consider getting fixed-wing pilots trained up on the device. A special licence is required to operate the drone, but this is also considerably less expensive than gaining a regular pilot’s licence.

For more information on companies in this article

Related Content

  • Cost-effective innovative backfill recycling
    April 12, 2012
    Day Aggregates offers a novel materials recycling approach - Kristina Smith reports Here's a neat idea: take the muck from utilities trenches, treat it and reuse it, saving between 30-40% on the cost of landfill and backfill. This, in essence, is the theory behind Day Aggregates' EcoFILL 40 material. Confident of a growing market for this type of product, Day has invested over €569,000 (£500,000) in a new plant at its 3.4ha site in south London. "There is great demand for a solution to waste streams
  • Advances in materials testing
    April 10, 2012
    Quicker, better, more cost effective materials testing - Kristina Smith writes. Most developments in materials testing technology involve updating and upgrading existing machines, either to meet changes to standards or to satisfy new needs in the market. And occasionally, a manufacturer will come up with something completely new. PUMA - the precision unbound materials analyser - falls into the latter category. It has been developed by Cooper Research Technology and Nottingham Transportation Engineering Cen
  • Sustainable road development in discussion at Intermat
    February 27, 2012
    An in-depth congress is being held in conjunction with the Intermat exhibition. Visitors to the show will be able to find out about the latest developments in sustainable road construction by attending this congress, which is being organised by the Committee for European Construction Equipment (CECE).
  • Prolec’s new variant PME500 machine engine
    September 26, 2013
    Prolec has launched the latest variant of its Prolec Machine Engine (PME), PME500, and can now offer a full range of control and safety functions for the construction industry in one unit. PME is a modular, integrated system that can manage both safety and efficiency functions in one system, where previously multiple systems were needed. PME500 controls load and a full 3D machine envelope, combining all functions of the Prolec control and safety range, and is available as a stand-alone system, or as a