Toro previews compact utility loader

Compact utility loader specialist The Toro Company previewed the newest member of its Dingo range, the TX 1000, at INTERMAT 2015. Due for launch in summer 2015, the machine will have a rated operating capacity exceeding 454 kg, says the company. When the loader arms are fully-extended, the hinge pin will measure 206 cm from the ground for reaching over the side of dumpsters and trucks. The vertical lift loader arm design keeps the load closer to the machine to allow operators to lift more weight with greate
January 6, 2017 Read time: 2 mins
The Dingo TX525 compact utility loader
Compact utility loader specialist The 8071 Toro Company previewed the newest member of its Dingo range, the TX 1000, at INTERMAT 2015. Due for launch in summer 2015, the machine will have a rated operating capacity exceeding 454 kg, says the company. When the loader arms are fully-extended, the hinge pin will measure 206 cm from the ground for reaching over the side of dumpsters and trucks. The vertical lift loader arm design keeps the load closer to the machine to allow operators to lift more weight with greater confidence. The TX 1000 comes in two options: a narrow track model weighing 1,184 kg and a wide-track model weighing 1,266 kg.¬¬¬ The TX 1000 represents a major upgrade on the company’s well established TX 525 utility loader that was on show at INTERMAT.

Toro also offers the DD4045 horizontal directional drill that features a 160-horsepower 196 Cummins QSB4.5 diesel, liquid-cooled engine and an on-board, infinitely variable drilling fluid pump that delivers a flow of up to 264.9 l/min.

For more information on companies in this article

Related Content

  • Innovation abounds at the smaller end of the compaction equipment sector
    August 22, 2013
    New machines are now being offered at the compact end of the asphalt compaction market - Mike Woof reports Manufacturers have developed an array of new machines and solutions for the compact end of the asphalt compactor market segment. These units have been designed to meet the latest regulations for Europe and the US, with low emission engines that are also more economical on fuel. But as these machines are made in large volumes, the market for smaller asphalt compactors sees fierce rivalry between fi
    Read More
  • XCMG is widening its already extensive model range with the addition of new machines
    October 16, 2013
    From XCMG comes an array of new machines for loading and hauling as well as road construction. Designed for the domestic market, the LW800K LNG is a 28.5tonne wheeled loader powered by a 257kW Weichai diesel and using LNG as fuel. Twin 500litre gas tanks sit just behind the cab and the machine is suited to duties in sites where emissions may be an issue. The machine features ZF axles and a ZF transmission. Standard bucket size is 4.5m3 and it can carry an 8tonne load. This is the latest addition to the fi
    Read More
  • New paving range
    February 8, 2012
    Several key additions to Dynapac's equipment line-up will extend the firm's machine range for the road construction market. Paving, planer and compaction lines will benefit from new machines, with president Claes Ahrengart emphasising the investment in research and development Dynapac continues to make.
    Read More
  • Doosan’s new DX140LC-3 and DX160LC-3 crawler excavators
    June 24, 2013
    Both machines are powered by Doosan’s DL06K ‘common rail’ six-cylinder turbocharged diesel engine, said to meet Stage IIIB engine emission regulations through the use of EGR (Exhaust Gas Recirculation) and Diesel Particulate Filter (DPF) after-treatment technologies. The engine has a displacement of 5,890cm³ and is said to deliver 15% more power [82 kW @ 1850RPM] than previous Stage IIIA models. The engine also delivers 11% more torque (49.5kgf.m) in the DX160LC-3 model. Doosan said that factory tests had
    Read More

Highlighted Content