Tilting Sensed

Tilting sensed Rugged inclinometers and tilt sensors are offered by Axiomatic, which has a series of new low cost units that can measure ±90º degrees or 360 degrees angular rotation. The angles are measured by a two-axis MEMS sensor, which senses acceleration caused by gravity. In a tilt sensor application, an out-of-range state can be transmitted as one of its outputs. The latest AX06025X series features CANopen networking, an RS-232 port or three Voltage outputs for communicating the angular measurement.
February 6, 2012 Read time: 2 mins
Axiomatic says that its rugged tilt sensors suit duties on earthmoving machines such as elevators
Tilting sensed Rugged inclinometers and tilt sensors are offered by 1532 Axiomatic, which has a series of new low cost units that can measure ±90º degrees or 360 degrees angular rotation. The angles are measured by a two-axis MEMS sensor, which senses acceleration caused by gravity. In a tilt sensor application, an out-of-range state can be transmitted as one of its outputs.

The latest AX06025X series features CANopen networking, an RS-232 port or three Voltage outputs for communicating the angular measurement. The inclinometer series also supports the SAE J1939 CAN interface under the p/n's AX0602XX. The J1939 inclinometer is fully configurable using the Axiomatic Electronic Assistant programming tool for PCs. All units are packaged for an IP67 rating with M12x2 5-pin connectors or M12 x1 5-pin. The inclinometer is designed to measure inclination angle in two orthogonal sensing directions X and Y in the range of up to ±90º. If vertically installed, it can measure an inclination angle in one sensing direction in the ±180º (0-360º) range.

For more information on companies in this article

Related Content

  • Sophisticated new asphalt compactors now coming to market
    March 4, 2015
    Emissions legislation is one factor driving the introduction of new compaction machines for Europe and North America, while customers in other markets are also benefiting from new technology - Mike Woof writes. The phased introduction of new exhaust emissions requirements for construction equipment being used in Europe and North America have had a major impact on new model development. In the asphalt compactor segment, manufacturers have had to redesign machines to pack in the latest emissions control techn
    Read More
  • Sophisticated new asphalt compactors now coming to market
    March 4, 2015
    Emissions legislation is one factor driving the introduction of new compaction machines for Europe and North America, while customers in other markets are also benefiting from new technology - Mike Woof writes. The phased introduction of new exhaust emissions requirements for construction equipment being used in Europe and North America have had a major impact on new model development. In the asphalt compactor segment, manufacturers have had to redesign machines to pack in the latest emissions control techn
    Read More
  • Chinese firms unveiled earthmoving innovation at BICES 2015
    January 15, 2016
    Chinese firms LiuGong, Shantui, Sunward and XCMG revealed innovative earthmoving concepts at BICES 2015 – Mike Woof writes. Of the many new machines seen at the recent BICES 2015 construction equipment exhibition in Beijing, a number of firms were notable for their innovations. LiuGong, Shantui, Sunward and XCMG all offered particular developments in earthmoving technology that stood out from the array of more conventional equipment. All of these firms also showed more standard machines, as did other rivals
    Read More
  • Machine control innovations
    February 15, 2012
    THE RECENT CONEXPO-CON/AGG exhibition has seen the launch of a wealth of new machine control technologies - Mike Woof reports A fast pace of technological development in the machine control sector is seeing new innovations come to market at regular intervals. The developments remain focussed on the three main technology suppliers to this market, Leica Geosystems, Topcon and Trimble, offereng a combination of systems using machine control based on GPS, total station, sonic units and industrial inertial gu
    Read More

Highlighted Content