MOBA’s PAVE-IR system helps boost asphalt paving quality

The advanced PAVE-IR system from MOBA is said to help improve mat quality control during asphalt paving operations. This system is mounted on the paver and scans back and forth across the paving mat immediately behind the machine’s screed. Data on the thermal image of the mat is then displayed on a screen for the operator to see, as well as being recorded for documentation purposes and later analysis if required.
March 27, 2015 Read time: 2 mins
MOBA’s heat scanner allows for efficient paving processes

The advanced PAVE-IR system from 1228 MOBA is said to help improve mat quality control during asphalt paving operations. This system is mounted on the paver and scans back and forth across the paving mat immediately behind the machine’s screed. Data on the thermal image of the mat is then displayed on a screen for the operator to see, as well as being recorded for documentation purposes and later analysis if required.

The system allows the paver operator to see the temperature gradient across the mat and identify and cold spots that may cause further trouble. Areas falling in temperature can also be compacted first, so as to ensure they are rolled out while still in the workable heat zone. Problems with the mat can also be identified and dealt with early on.

The system uses an intelligent temperature scanner over the entire paving width of up to 12m to measure the temperature of the asphalt at up to 61 measurement points. The temperature profile is shown in real-time on a display. As a result, the operator can react at any time if irregularities occur.

In addition, the profile is stored with the GPS position data and transferred to a USB stick. Using a software, the contractor can evaluate and document the data in the office, can use it for planning subsequent work and to document the quality of his or her work. At the same time, this analysis can be used to better understand the whole process of road construction and to improve the quality in the long term.

For more information on companies in this article

Related Content

  • Dynapac is broadening its range for asphalt paving
    April 1, 2014
    Atlas Copco’s Dynapac brand is launching new models aimed at the asphalt paving market - Mike Woof reports Atlas Copco’s Dynapac brand looks set to boost its worldwide presence in the road construction market, with new asphalt paving products forming a major segment of the firm’s improved portfolio. The launch of new pavers and an improved material feeder comes at a busy time for the Dynapac brand. When Dynapac was first acquired by Atlas Copco the business was left separate initially, however it has now
    Read More
  • Stepless spraying up to 7m with Dynapacs SD2500CS PROTAC Spray Paver
    April 11, 2024
    Efficiency goes hand in hand with intelligence in the Dynapac SD2500CS PROTAC Spray Paver. The PROTAC brings two processes together in one machine and in a single operation: paving and spraying. It applies simultaneously a layer of tack coat emulsion and a layer of asphalt. This not only saves time and therefore costs, but also increases the pavement quality.
    Read More
  • Airport runway rebuild at Bologna
    May 15, 2019
    Rebuilding a runway requires special attention to detail to maximise efficiency and safety Airport runways face special challenges with regard to the loads they carry on a daily basis, particularly when aircraft are landing. A modern jet aircraft will typically land at speeds of around 240-260km/h, with a laden 747 weighing as much as 265tonnes at the end of a long flight. The stresses these large aircraft place on runway surfaces are enormous and not just with the massive impact forces exerted during
    Read More
  • Machine and machine control innovations in concrete paving
    June 28, 2013
    Machine innovations and machine control advances are the latest news in the concrete paving sector - Mike Woof reports. While machine control systems were pioneered in the concrete paving market, continuous refinement of the technologies is offering major improvements for customers. Customers have a choice now of more than one supplier while the packages are said to be more user-friendly than before. And in addition, the systems themselves can be more closely integrated into the machines due to advances mad
    Read More

Highlighted Content