Skip to main content

Trial of innovative real-time alerts for wildlife on highways

The Colorado Department of Transportation (CDOT) is testing a first-in-the-USA detection system that alerts drivers in real time of wildlife on highways that cause risk to motorists. The OmniTrax solution from Senstar is based on a volumetric electromagnetic proven sensor, buried approximately one third of a metre underground and about 10 metres from either side of the roadway.
May 2, 2012 Read time: 3 mins
The 5406 Colorado Department of Transportation (CDOT) is testing a first-in-the-USA detection system that alerts drivers in real time of wildlife on highways that cause risk to motorists. The 5408 OmniTrax solution from 5407 Senstar is based on a volumetric electromagnetic proven sensor, buried approximately one third of a metre underground and about 10 metres from either side of the roadway. The sensor detects large animals such as deer or elk, crossing over it, locates the position of the intrusion to within a metre and then activates nearby signs, in order to alert drivers approaching the high risk segment.

The current test installation covers 1.6kms of US 160 between Durango and Bayfield in southwest Colorado (around milepost 96), with six signs on each side. Once an animal is detected, the relevant two signs on each side light up.

“CDOT, in coordination with the Division of Wildlife studied many solutions, evaluating their practicality and economic and environmental feasibility,” explains Kevin Curry, a professional engineer with CDOT. “Fencing, permanent signs and lighting were not quite right for this stretch. We needed ways to minimise the impact to the wildlife’s migration while alerting motorists of their presence. We needed a solution with minimal environmental impact.”

Curry says that alternative detection systems using laser beams, microwaves or infrared technology were considered, but due to the potential for false alarms caused by snow, clouds and even tree branches, Omnitrax was clearly the best option with its high performance rating and low probability of false alarms.

Paul Trouten, national sales manager for Senstar says that Omnitrax is widely used for securing perimeters of strategic facilities, such as airports, military installations, borders, major energy and utilities installations and prisons, around the world.

“CDOT’s pilot project is a new and innovative application for the product,” said Trouten.  He added that the company has received numerous calls of inquiry based on the Colorado application.
Seven speed radar detectors have also been installed to register motorists’ speed both outside and inside the test zone so that drivers’ base speed and reaction speed can be monitored. The radar system will also monitor traffic counts, useful for follow-up analysis of the data by the CDOT’s traffic & safety staff.

The project was awarded a CDOT Research Grant for $150,000 that is going to the 3181 Western Transportation Institute of Bozeman, Montana, to independently evaluate the success of the project.

Related Content

  • Green is good for road construction with National Highways
    July 25, 2024
    Green technology is now good for road construction with National Highways.
  • Using ITS to maximise safety and traffic flow for cycling
    January 22, 2013
    Copenhagen, Denmark, has long been known as one of the world’s leading cities for cycling. In some areas of the city, the modal share of bikes has reached a level of as much as 50 %. And on some of the most frequently used bike paths the average daily number of cyclists is close to 30,000. As these numbers continue to rise, new ways of planning and implementing cycling infrastructure are needed. Increasingly, Danish traffic planners are turning to technology as a tool for planning cycling infrastructure. I
  • Brazil weighs its WIM options
    July 21, 2021
    Recent legislation in Brazil is allowing greater use of weigh-in-motion technology, all in an attempt to address some familiar challenges, writes Intercomp's Jon Arnold.
  • Weighty matters for developing countries
    November 6, 2012
    One leading Weigh in Motion technology manufacturer is helping governments in developing countries reduce excessive road damage, while several others have seen their latest WIM systems recently used on the highways of Eastern Europe. Guy Woodford reports Recent Central Weighing WIM installations in Bangladesh are helping its national government reduce the financial burden of excessive road damage, while also protecting many bridges that are vital to transport and trade. The need for such installations was e