The IRF has an online safety seminar

The IRF is carrying out an online safety seminar on 27th September. This will be held at 11am US Eastern time. The seminar will highlight key issues such as maintenance tasks being carried out on high speed, high traffic volume roads at night. While these night time work zones do cause less traffic congestion due to the reduced traffic volumes, they can be very dangerous for both motorists and workers if they are not properly designed. Many traffic accidents happen at night due to drivers who are drinking o
September 23, 2013 Read time: 2 mins
The IRF is carrying out an online safety seminar on 27th September. This will be held at 11am US Eastern time. The seminar will highlight key issues such as maintenance tasks being carried out on high speed, high traffic volume roads at night. While these night time work zones do cause less traffic congestion due to the reduced traffic volumes, they can be very dangerous for both motorists and workers if they are not properly designed. Many traffic accidents happen at night due to drivers who are drinking or are overly tired. It can be difficult for drivers to navigate through a work zone because they cannot see the changes in the traffic pattern. Work zones by nature can be hazardous for workers. Trying to do this work at night without proper illumination adds to the dangers for workers. In addition, these workers are constantly in fear of errant motorists who may make mistakes near their work area thereby threatening their well-being, if not also their lives.  

Jameson Guthrie, the international manager for Wanco and Mike Dreznes, executive vice president of the 713 International Road Federation will use this IRF event to introduce state of the art technologies and best practices being use around the world to make these night time construction zones safer for both motorists as well as workers.

Concepts to be discussed will include portable lighting technologies, reflective clothing for workers, arrow boards and variable message signs that are used to give motorists proper advanced knowledge of the upcoming work zones as well as portable barriers, crash cushions and truck mounted attenuators that should be used to reduce the negative consequences of mistakes caused by errant motorists in a work zone. This webinar will provide important information for and public or private agencies responsible for design or maintenance of crash cushions. This includes DOTs, consultants, academia, contractors and asset management organisations. Contractors are strongly encouraged to participate in this 90 minute webinar.

For more information on companies in this article

Related Content

  • Research finds plastic-covered barriers aid motorcyclist safety
    September 1, 2015
    Tests carried out by VTI, the Swedish National Road and Transport Research Institute, involving motorcycles and crash barriers have shown that a plastic covering on the sharp edge at the top of the barrier can help save the lives of motorcyclists.
    Read More
  • Alarming results from US distracted driving survey
    May 16, 2013
    Transurban-Fluor and AAA Mid-Atlantic have published an alarming report on distracted driving on the busy I-95 highway in Northern Virginia in the US. The two bodies have launched a regional campaign focused on reducing distracted driving in the 95 Express Lanes construction zone. According to the report, almost all (94%) of frequent I-95 drivers have seen someone engage in dangerous, distracted behaviour while driving on this busy commuter route. In addition, more than half (56%) of I-95 drivers use their
    Read More
  • Taking responsibility could cut crashes
    December 23, 2015
    In discussing road safety, the same issues tend to crop up time and time again. Technology is often seen as a major way forward for cutting the death toll. This ignores the fact that many drivers simply use their vehicles to the limits of their capabilities and that cars with ABS or ETSC for example are simply driven faster and with less regard for other road users or the surrounding road environment.
    Read More
  • Industry AMS opts for safety in any direction
    January 25, 2017
    Italian company AMS explains how its crashworthy end terminals act like a crash cushion Industry AMS (Automation Manufacturing Services) has developed a crashworthy end terminal tested according to part 7 of the EN 1317 that is classified as a double-sided and bi-directional end terminal. Starting from the European version of the terminal, and based on the same architecture, AMS has designed the SMA (Safety Modular Absorber) as a reinforced end-terminal in order to be complaint with both the MASH and
    Read More

Highlighted Content