Colorado adopting new road surface standard

The Colorado Department of Transportation (CDOT) is implementing a new pavement texture standard. This revised specification is a response to feedback from the state's drivers with requirements for finishing Portland cement concrete pavement (PCCP). The main change is that the state is discontinuing the use of tining on all PCCP projects. In certain instances the grooved pavement texture produced by longitudinal tining can cause drivers to experience uncomfortable lateral vehicle movement. This is called gr
June 27, 2013 Read time: 2 mins
Transtec carried out extensive tests to ensure that CDOT’s revised surface specification would ensure sufficient skid resistance and safety for road users
The 5406 Colorado Department of Transportation (CDOT) is implementing a new pavement texture standard. This revised specification is a response to feedback from the state's drivers with requirements for finishing Portland cement concrete pavement (PCCP). The main change is that the state is discontinuing the use of tining on all PCCP projects. In certain instances the grooved pavement texture produced by longitudinal tining can cause drivers to experience uncomfortable lateral vehicle movement. This is called groove wander and CDOT's pavement design programme manager Jay Goldbaum explained that the state fully-investigated the practicality of moving away from longitudinal tining to address this ride comfort issue. The specification update is a result of CDOT's long-term study of PCCP textures used within the state, including analysis of texture, friction, noise, and accident records. This study was carried out by specialty pavement engineering firm The 5943 Transtec Group. But the texturing methods now required by the specification should not have an adverse effect on the safety of CDOT's pavements. CDOT's updated PCCP specifications require contractors to finish their pavement by broom, burlap or turf drag, or diamond grinding. According to Dr Robert Rasmussen, PE, vice president and chief engineer of Transtec, "Drag and diamond ground textures can be simple to construct, and they are capable of producing smooth and quiet pavement surfaces."

In addition to meeting CDOT's standards for safety and ride comfort, "The new specification will be easier to monitor," said Goldbaum. The standards require pavement texture to be verified with CDOT's CP-77B volumetric method test.

For more information on companies in this article

Related Content

  • Putting roller compacted concrete to the test
    June 28, 2013
    Although it has been around since the 1970s, roller compacted concrete (RCC) is starting to look a whole lot more attractive, thanks to the rising price of bitumen. Now the challenge is to define specifications and tests to help ensure quality - Kristina Smith reports. At a meeting of the American Concrete Pavement Association in December 2011, there was a sea-change in the attitude towards roller compacted concrete (RCC). Up until that point, the feeling among the 400-plus members, of which half are contra
    Read More
  • Advances in bitumen technology will boost surface wear life and quality
    September 19, 2012
    From chip fat to banana bags, the race is on to find new bitumen additives which will solve two problems with one solution: replace diminishing petrochemical-based products and make use from waste rather than landfilling it - Kristina Smith reports It is not just the desire to preserve our environment which is driving the industry’s search for products which don’t eat up raw materials. The hunger of emerging economies – particularly China – mean that resources can be hard to come by, so it makes sense for s
    Read More
  • Demand for asphalt testing solutions
    February 14, 2012
    Asphalt testing is performed for a variety of reasons by a variety of companies. Patrick Smith reports Road safety is in the interest of everyone and today it is also an important target shared by the majority of the companies involved in road design and construction. The growing attention paid to this value has had a remarkable effect on the material testing field, encouraged by an increasing market demand for testing solutions as well as by the new technical requirements established by international st
    Read More
  • Bridge inspection: destructive versus non-destructive methods
    January 6, 2015
    Tens of thousands of bridges in the United States are in desperate need of repair. But where to begin analysing their deteriorating state? Roger Roberts* investigates tips and techniques for ensuring bridge safety The average age of America’s more than 600,000 crumbling bridges is 42 years – many are 60 to 80 years old. The situation is dire, with many described as functionally obsolete, according to the American Society of Civil Engineers’ latest edition of its Report Card for America’s Infrastructure.
    Read More

Highlighted Content