Colorado adopting new road surface standard

The Colorado Department of Transportation (CDOT) is implementing a new pavement texture standard. This revised specification is a response to feedback from the state's drivers with requirements for finishing Portland cement concrete pavement (PCCP). The main change is that the state is discontinuing the use of tining on all PCCP projects. In certain instances the grooved pavement texture produced by longitudinal tining can cause drivers to experience uncomfortable lateral vehicle movement. This is called gr
June 27, 2013 Read time: 2 mins
Transtec carried out extensive tests to ensure that CDOT’s revised surface specification would ensure sufficient skid resistance and safety for road users
The 5406 Colorado Department of Transportation (CDOT) is implementing a new pavement texture standard. This revised specification is a response to feedback from the state's drivers with requirements for finishing Portland cement concrete pavement (PCCP). The main change is that the state is discontinuing the use of tining on all PCCP projects. In certain instances the grooved pavement texture produced by longitudinal tining can cause drivers to experience uncomfortable lateral vehicle movement. This is called groove wander and CDOT's pavement design programme manager Jay Goldbaum explained that the state fully-investigated the practicality of moving away from longitudinal tining to address this ride comfort issue. The specification update is a result of CDOT's long-term study of PCCP textures used within the state, including analysis of texture, friction, noise, and accident records. This study was carried out by specialty pavement engineering firm The 5943 Transtec Group. But the texturing methods now required by the specification should not have an adverse effect on the safety of CDOT's pavements. CDOT's updated PCCP specifications require contractors to finish their pavement by broom, burlap or turf drag, or diamond grinding. According to Dr Robert Rasmussen, PE, vice president and chief engineer of Transtec, "Drag and diamond ground textures can be simple to construct, and they are capable of producing smooth and quiet pavement surfaces."

In addition to meeting CDOT's standards for safety and ride comfort, "The new specification will be easier to monitor," said Goldbaum. The standards require pavement texture to be verified with CDOT's CP-77B volumetric method test.

For more information on companies in this article

Related Content

  • Ground penetrating radar used to investigate tunnel deterioration
    May 13, 2015
    Using ground penetrating radar to determine reason for serious pavement settling in Kentucky-Tennessee tunnel Just a few years after the opening of the Cumberland Gap Tunnel, highway officials noticed moderate to severe settling of the continuously reinforced concrete pavement. The mountain tunnel provides an important link between Kentucky and Tennessee along US25E and the problem looked serious, with many voids discovered beneath the pavement surface. To investigate the problems, the Kentucky Transpor
    Read More
  • Skid resistant road surface reduces accidents
    February 21, 2012
    Following a programme of road surface retexturing at five sites to improve skid-resistance, Aberdeenshire Council in Scotland has seen a 100% reduction in crashes and loss of control incidents in the eight months since treatment.
    Read More
  • Brazilian contractor uses novel methods for high quality road
    January 5, 2015
    Cold-in place recycling method provides fast road rebuild in Brazil In Brazil a road contractor has carried out a high quality road rebuilding job, using novel techniques. Contractor Brown Brown is located in Santa Teresinha in the state of Bahia and recently carried out a two-week job for the company to rehabilitate sections of highway BR-381. The highway is an important route in Brazil and runs from Sao Paulo to Belo Horizonte. Highway BR-381 or Rodovia Fernão Dias, as it is called, stretches some 576km
    Read More
  • CECE 2018 conference Rome: the sector powers up for digitisation
    March 20, 2019
    Getting the human-machine interface for equipment automation right is a lot trickier than expected. David Arminas reports from the CECE conference in Rome For many contractors, digitisation is key for improving on-site operational efficiency. But it may be time to take stock of progress and examine what does and doesn’t work. That is not to say that the anchors should be thrown out to halt development. Far from it. In the past eight months, the CECE - Committee for European Construction Equipment – led
    Read More

Highlighted Content