Skip to main content

Swedish motorcycle test

In Sweden crash testing has been carried out using motorcycles for the first time. Four crash tests were carried out at the VTI crash laboratory in Linköping, Sweden, for the client, the insurance company Folksam. As a result, Swedish motorcyclists can expect safer barriers according to VTI, the Swedish National Road and Transport Research Insitute. The VTI have participated in two different projects with focus on better safety for motorcyclists. The first project was run in cooperation with the Swedish Mo
November 10, 2015 Read time: 2 mins
In Sweden crash testing has been carried out using motorcycles for the first time. Four crash tests were carried out at the 7264 VTI crash laboratory in Linköping, Sweden, for the client, the insurance company Folksam. As a result, Swedish motorcyclists can expect safer barriers according to VTI, the Swedish National Road and Transport Research Insitute.

The VTI have participated in two different projects with focus on better safety for motorcyclists. The first project was run in cooperation with the Swedish Motorcyclists Association (SMC) and the Swedish parapet and barrier association (SVBRF). This studied existing literature to describe state-of-the art in motorcycle to barrier crash interaction. In the second project, initiated by Folksam, four full-scale crash tests on barriers with different kinds of protection was executed.

The joint result from these two projects opened a possibility to run a final crash test with a simple prototype of a plastic cover to shield the sharp edge on the top of the barrier. According to VTI, this prototype will help reduce injuries to motorcyclists in the event of an impact. In the various tests, different kinds of motorcycle protection systems were installed on a traditional W-beam and sigma post barriers.

The cover will let the motorcyclist slide along the barrier instead of getting stuck, lowering the severity of injuries.

The positive outcome is all about covering sharp edges and protruding parts, including the posts of the barrier. The plastic tube is a cheap and simple way of demonstrating a principle but it is yet not a finished product according to VTI.
The VTI crash laboratory is an accredited test facility for the EN1317 European test procedure for barriers. Being part of the international work with the procedure research engineer at the VTI crash laboratory, Jan Wenäll, will bring this experience to the ongoing development of an additional procedure for motorcyclists addition to the same procedure.

For more information on companies in this article

Related Content

  • Road markings important for road safety
    February 20, 2012
    Manufacturers are constantly upgrading marking materials and equipment. Now those responsible for highways are being asked to do more as Patrick Smith reports. A recent report claimed that nearly one-third of the length of Britain's single carriageway A-roads have white lines so worn out that they do not meet recognised standards. According to the LifeLines Report, an assessment of more than 2,400km of the road network, Britain's most dangerous roads have the most worn-out centre line markings of all, leavi
  • Challenging Colombian tunnel completed
    May 30, 2024
    A tunnel stretch on Colombia’s Santa Fe - Cañasgordas highway is complete – Mauro Nogarin reports
  • Zipping up road lanes
    September 28, 2018
    QMB has a Lindsay Road Zipper on duty near Montreal. World Highways deputy editor David Arminas climbed aboard As vice president of Canadian barrier specialist QMB, based in Laval, Quebec, Marc-Andre Seguin is sanguine about the future for moveable barriers. On the one hand, it looks good. The oft-stated advantage of moveable barriers is that the systems are cheaper to install than adding a lane or two to a highway or bridge. Directional changes to lanes can boost volume on a road without disrupting tra
  • Durability is crucial while warm mix technology can help disaster recovery
    February 21, 2013
    Why durability is crucial for both emerging and developed economies, and how warm mix technology can help disaster recovery - Kristina Smith reports. When CORE Construction, a 100% owned Ghanaian company, started working on road construction projects five years ago, it was difficult to source the right bituminous mixes. “In the past, most construction firms had a number of challenges when it came to bituminous works, since the local capacity was not well-developed,” said CORE CEO Frank Lartey. CORE’s soluti